Page 2 - TABLE OF CONTENTS
INST ALLA TION MANUAL TABLE OF CONTENTS 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Cleaning and Maintenance . . . . . . . . . . . . . . . . . 6 MotorGrease FiltersNon-Ducted Recirculation Fi...
Page 3 - SAFETY; READ AND SAVE THESE INSTRUCTIONS; INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.; WARNING
INSTALLATION MANUAL SAFETY 3 READ AND SAVE THESE INSTRUCTIONS ! Intended for domestic cooking only ! INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. Register your range hood online at www.broan.com ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: • Use ...
Page 4 - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:; CAUTION
INST ALLA TION MANUAL SAFETY 4 ! WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b) Always turn hood ON when cooking at high hea...
Page 5 - Operation; Operate the hood as follows:; FAN SWITCH; Turns fan on to LOW speed.; Turns fan on to HIGH speed.; LIGHT SWITCH; Turns light on to LOW intensity.; II; Turns light on to HIGH intensity.
INSTALLATION MANUAL OPERA TION 5 Operation Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and fresher. Operate the hood as fol...
Page 6 - CLEANING AND MAINTENANCE; Cleaning and Maintenance; Avoid when choosing a detergent:; bleach
INST ALLA TION MANUAL CLEANING AND MAINTENANCE 6 Cleaning and Maintenance Proper maintenance of the Range Hood will assure proper performance of the unit. MOTOR The motor is permanently lubricated and never needs oiling. If the motor bearings make excessive or unusual noise, replace the motor with t...
Page 7 - TION; Install Ductwork (Ducted Installations Only)
INSTALLATION MANUAL INSTALLA TION 7 Recommended Tools and Accessoriesfor Installation • Measuring tape • Phillips screwdriver no. 2 • Flat blade screwdriver (to open knockout holes) • Drill, 1/8” drill bit and 1½” hole saw (to mark holes for ducting and cut electrical access hole) • 7/64” drill bit ...
Page 8 - INST; Contents; Make sure that the following items are included:
INST ALLA TION MANUAL INST ALLA TION 8 Contents Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included: BCSD Series : (2) G REASE F ILTERS (1) 3¼” X 10” D AMPER ASSEMBLY * (1) 7”...
Page 9 - Prepare the Hood
INSTALLATION MANUAL INSTALLA TION 9 Prepare the Hood 1 ] If present, remove all protective polyfilm from the hood and/or parts. 2 ] Using the tab, remove the grease filters from the hood by pushing down and tilting filters out. 3 ] Remove both screws holding damper assembly to hood. Remove parts bag...
Page 10 - NON-DUCTED INSTALLATION ONLY
INST ALLA TION MANUAL INST ALLA TION 10 5 ] Remove 7” Round Duct Plate from top/back of hood (see illustration below). RECIRCULATION COVER PLATE SCREWS 6 ] Remove Electrical Power Cable Knockout from top (vertical exhaust) or back (horizontal exhaust) of hood. Install an appropriate strain relief, 1...
Page 11 - DUCTED INSTALLATION ONLY; TIP; connection with the house duct work.; and
INSTALLATION MANUAL INSTALLA TION 11 DUCTED INSTALLATION ONLY TIP : Inser t a small length of duct over the 3¼” x 10” damper assembly (for rectangular ducting) or 7” round (for round ducting) and seal the joint using aluminum foil duct tape to ease connection with the house duct work. 8 ] Remove 3¼”...
Page 12 - Prepare the Hood Location; EZ1 One-person installation system; If replacing a hood and plan to use; Measure and mark the hood center line on cabinet bottom.
INST ALLA TION MANUAL INST ALLA TION 12 Prepare the Hood Location NOTE: Before star ting installation, read all the steps of these instructions.Use the illustration below to identify your kitchen cabinet type. EZ1 One-person installation system EZ1 installation is designed for use with kitchen cabin...
Page 13 - location on template.
INSTALLATION MANUAL INSTALLA TION 13 FRAMED CABINET 7/64” X Y Z Refer to the marking on the brackets to determine the correct installation side and orientation. Mate the corresponding bracket to the cabinet side frame, while placing rear end of bracket against the wall. Use a pencil to mark 3 hol...
Page 14 - Use a pencil to mark 3 holes.
INST ALLA TION MANUAL INST ALLA TION 14 [ \ 7/64” X 3 X Y Z Refer to the marking on brackets to determine the correct installation side and orientation. Align the corresponding bracket to the cabinet side, while placing rear end of bracket against the wall. Draw a line on the outer edge of the br...
Page 15 - While holding the hood
INSTALLATION MANUAL INSTALLA TION 15 A C B D Install the Hood (EZ1 Bracket) 1 ] Run house power cable between service panel and hood location. 2 ] There are 2 pairs of recessed holes on each side of the top of the hood (on rear: A and B , on front C and D on illustration below); these holes allow th...
Page 16 - ] For framed cabinet; , secure the hood to the cabinet using 4 no. 8 x 5/8” round head wood
INST ALLA TION MANUAL INST ALLA TION 16 FRAMED CABINET FRAMELESS CABINET 7 ] For framed cabinet , secure the hood to the EZ1 brackets using 4 no. 8-18 x 1/2” metal screws with washers (screws and washers included in parts bag). Insert 2 screws and washers per side, in the slots (as shown in inset on...
Page 17 - Standard Installation (without EZ1 Brackets)
INSTALLATION MANUAL INSTALLA TION 17 Standard Installation (without EZ1 Brackets) 1 ] Use the proper diagram below for placement of duct work and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole, only cut the hole for electrical wiring. 2 ] Install p...
Page 19 - Connect the Wiring
INSTALLATION MANUAL INSTALLA TION 19 Connect the Wiring 1 ] Connect House Power Cable to range hood wiring: BLACK to BLACK, WHITE to WHITE and GREEN or bare wire under GREEN ground screw. ! WARNING Risk of electric shock. Electrical wiring must be done by qualifi ed personnel in accordance with all ...
Page 20 - Install the Light Bulbs; Gently push upwards and turn clockwise until secure.; Install the Filters; Ducted Installation Only:; Re-install grease filters removed in step
INST ALLA TION MANUAL INST ALLA TION 20 Install the Light Bulbs 1 ] Align the bulb leads with the small indentations located on the border of the lamp location on hood (see inset above), then install the bulbs by placing the bulb leads into their grooves in the socket. 2 ] Gently push upwards and tu...
Page 21 - WIRING DIAGRAM
INSTALLATION MANUAL WIRING DIAGRAM 21 G/Y W BK O R F AN MO T O R BN BN/W G/Y R (Lo w) BK (High) W 120 V A C Line Neutr al Gr ound BK BK Mot or S witch Light S witch Y (Lo w) BL (High) W W BK BK COLOR CODE BK BL BN BLACK BLUE BROWN R W Y RED WHITE YELLOW BN/W G/Y O BROWN/WHITE GREEN/YELLOW ORANGE W 1...
Page 22 - SERVICE P; BCSD SERIES
INST ALLA TION MANUAL SERVICE P AR TS 22 BCSD SERIES R EPLACEMENT P ARTS AND R EPAIRS In order to ensure your unit remains in good working condition, you must use Broan-NuTone LLC genuine replacement parts only. Broan-NuTone LLC genuine replacement parts are specially designed for ...
Page 26 - ARRANTY
INST ALLA TION MANUAL W ARRANTY 26 Limited Warranty Warranty Period and Exclusions: Broan-NuTone LLC (the “Company”) warrants to the original consumer purchaser of its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship for a period o...
