Teledyne ECO#02-0227 - Manuals

Page 2 - TRACE OXYGEN ANALYZER; TELEDYNE ANALYTICAL INSTRUMENTS

INSTRUCTION MANUAL FOR TRACE OXYGEN ANALYZER MODEL 311XL TELEDYNE ANALYTICAL INSTRUMENTS 16830 CHESTNUT STREET CITY OF INDUSTRY, CA 91749 TELEPHONE: (888) 789-8168 (626) 934-1500 (626) 961-9221 FAX: (626) 961-2538 (626) 934-1651 Web: www.teledyne-ai.com

Page 3 - WARNING

WARNING The sensor(s) used in this instrument uses electrolytes which contain substances that are extremely harmful if touched, swallowed, or inhaled. Avoid contact with ANY fluid or powder in or around the unit. What may appear to be plain water could contain one of these toxic substances. SKIN CON...

Page 4 - TABLE OF CONTENTS

TABLE OF CONTENTS 311XL SERIES 1. INTRODUCTION 1 1.1 Description 1 1.2 Method of Analysis 1 1.3 Outstanding Features 1 1.3.1 Micro-Fuel Cell 1 1.3.2 Reliable Calibration 2 1.3.3 Integral Power Supply 2 1.3.4 Accuracy and Response 3 1.3.5 Compact Packaging 3 2. SUPPORTING EQUIPMENT AND SERVICES 4 2.1...

Page 5 - The Teledyne Analytical Instruments (TAI) Model 311XL and

311XL SERIES TRACE OXYGEN ANALYZER 1. INTRODUCTION 1.1 Description: The Teledyne Analytical Instruments (TAI) Model 311XL and 311TCXL are portable, intrinsically safe trace oxygen analyzer which can be operated without an external power source. These analyzers will be referred to as Model 311XL or 3...

Page 6 - Although this instrument can be calibrated with

1.3.2 Reliable Calibration. Although this instrument can be calibrated with air, the use of a calibration gas gives better results on the lower PPM ranges. If the instrument is exposed to high concentrations of oxygen (percent levels), it will take a significant amount of time to purge the oxygen fr...

Page 7 - Accuracy and Response; C and constant pressure after

A current limiting resistor (R1 and R2) is potted into the end of each battery. This assures that under no circumstances can more than 25 milliamperes (100 milliwatts) be switched or drawn from either battery supply. This means that the Model 311XL may be used in explosive atmospheres where arcs of ...

Page 8 - SUPPORTING EQUIPMENT AND SERVICES; The customer must provide a means of controlling the; Service

2. SUPPORTING EQUIPMENT AND SERVICES 2.1 Sampling Equipment. The customer must provide a means of controlling the pressure and flowrate of the sample gas. For positive pressure applications, TAI suggests a simple throttle valve installed in the sample line between the sample point and the analyzer. ...

Page 9 - Calibration Procedure.

3.1 Introduction. The Model 311XL is supplied completely assembled and ready for instant use. The Micro-Fuel Cell must be installed prior use. When a sensor is first installed, the instrument should be purged for 12-16 hours with zero gas (an inert gas such as nitrogen or argon with less than 0.1 pp...

Page 10 - When connecting the instrument to a positive

Span gas: An inert gas (nitrogen or argon) with a known trace amount of oxygen. The oxygen content should be 70 – 90% of the full scale on the range of interest (working or primary range). Note, if this instrument is exposed to high concentrations of oxygen (percent levels), it will take a significa...

Page 11 - If the sample is at atmospheric pressure (or; Battery Power Supply Service.; The Model 311XL is designed to be

2) Establish a flowrate in the sample line of from 0.2 to 5 liters/min. Allow the sample to flow long enough to allow a stable low reading to be achieved. When disconnecting the instrument, reverse the procedure: source fitting first, and then vent fitting. The objective of the connection -- disconn...

Page 12 - The amber charge lamp (on the rear of the case) will be lit; Beyond adhering to a battery recharge schedule, no

that an overnight recharge be accomplished every three (3) weeks of continuous use. To recharge the batteries, place the range switch in the “OFF” position and connect the power cord to a convenient outlet. NOTE: The amber charge lamp (on the rear of the case) will be lit during charging process. Th...

Page 16 - Accuracy at 25; SYSTEM OPPERATING TEMPERATURE:

Accuracy at 25 o C and constant pressure after thermal equilibrium has been reached. Basic accuracy +/- 2% of full scale for all ranges except 0-2 PPM range. Accuracy for 0-2 PPM range (+/- 5% of full scale). Accuracy over the temperature range 0-35C at constant pressure after thermal equilibrium ha...

Page 18 - DRAWING LIST

C-70246 SCHEMATIC D-70268 OUTLINE C-14627 WIRING DIAGRAM (110 VAC) C-10470 WIRING DIAGRAM (220VAC) DRAWING LIST MODEL 311TCXL C-70248 SCHEMATIC D-70270 OUTLINE C-41661 WIRING DIAGRAM (110 VAC) C-37938 WIRING DIAGRAM (220VAC) NOTE: The MSDS on this material is available upon request through the Teled...