Star Trac Sep-90 - Manuals

Star Trac Sep-90 – Manual in PDF format online.

Manuals:

Manual

Manual Star Trac Sep-90

Summary

Page 2 - Training Manual; Components that connect to the display electronic:

Training Manual STAR TRAC FITNESS 2 of 22 637-1376 Rev: A Components that connect to the display electronic:

Page 3 - –The main keypad that is used to enter commands.; Center Console, Basic; –The small keypad that has the ‘Quick Start’ key. If the unit has any

Training Manual STAR TRAC FITNESS 3 of 22 637-1376 Rev: A A. Display Panel (J7 – 12 pin connector) –The main keypad that is used to enter commands. B. Center Console, Basic (J8 – 6 pin connector) –The small keypad that has the ‘Quick Start’ key. If the unit has any kind of entertainment, there will ...

Page 4 - CSAFE Power; – The external CSAFE port.

Training Manual STAR TRAC FITNESS 4 of 22 637-1376 Rev: A C. CSAFE Power (J10 – 6 pin connector) – The external CSAFE port. Note: This port is only used to supply power to external add on audio accessories. D. Polar Receiver (J11 – 3 pin connector) – The telemetry/wireless heart rate plugs in here (...

Page 5 - – The contact heart rate board plugs in

Training Manual STAR TRAC FITNESS 5 of 22 637-1376 Rev: A E. Contact Heart Rate (6 pin connector on the standoff heart rate board) – The contact heart rate board plugs in here. The contact heart rate board is typically mounted on the display electronics.

Page 6 - – The small keypad at the top of the display housing.

Training Manual STAR TRAC FITNESS 6 of 22 637-1376 Rev: A F. Fan Keypad (J1 – 8 pin connector) – The small keypad at the top of the display housing. G. Fan Power (J3 – 2 pin connector) – The fan gets power from the display electronic.

Page 7 - – The primary port for uploading

Training Manual STAR TRAC FITNESS 7 of 22 637-1376 Rev: A H. Primary Port (J6 – 10 pin connector) – The primary port for uploading software into the display. I. Secondary Port (J5 – 10 pin connector) – The secondary port for uploading software into the display.

Page 8 - – This is the main cable that connects the display to the LCB.

Training Manual STAR TRAC FITNESS 8 of 22 637-1376 Rev: A J. Display Cable (J4 – 12 pin connector) – This is the main cable that connects the display to the LCB. The display cable is like the nerves of the stepper. Information and power are sent up to the display and back down to the LCB to control ...

Page 9 - L. HR Board Ground Cable –; connects to the display frame.

Training Manual STAR TRAC FITNESS 9 of 22 637-1376 Rev: A K. TV Interface (J9 – 7 pin connector) – NEVER use this port. L. HR Board Ground Cable – connects to the display frame.

Page 10 - Used for PVS and on “Made for iPod” kits only.

Training Manual STAR TRAC FITNESS 10 of 22 637-1376 Rev: A M. CCB (J14 – 7 pin connector) Used for PVS and on “Made for iPod” kits only.

Page 13 - This is where the LCB receives the signal from the RPM Sensor.

Training Manual STAR TRAC FITNESS 13 of 22 637-1376 Rev: A Connections and Components that plug into the LCB (PN: 711-3162) A. RPM Sensor Connector (J1 – 4 pin connector) – This is where the LCB receives the signal from the RPM Sensor.

Page 14 - Brings in the power from the alternator and controls the

Training Manual STAR TRAC FITNESS 14 of 22 637-1376 Rev: A B. Alternator Cable Connector (J2 – 10 pin connector) – Brings in the power from the alternator and controls the resistance on the pedals. The battery cables are included with this connector to supply power for pause. . C. Resistor Connector...

Page 15 - This is where the external CSAFE cable plugs in to the LCB for

Training Manual STAR TRAC FITNESS 15 of 22 637-1376 Rev: A D. CSAFE Data Connector (J3 – 8 pin connector) – This is where the external CSAFE cable plugs in to the LCB for data transfer. E. Display Cable Connector (P1 – 12 pin connector) – Information and power are sent up to the display and back dow...

Page 16 - Software Uploading Connector (JP1 – 10 pin connector) –; This is used to load software into the LCB.

Training Manual STAR TRAC FITNESS 16 of 22 637-1376 Rev: A F. Software Uploading Connector (JP1 – 10 pin connector) – This is used to load software into the LCB.

Page 17 - Other Electrical Components; Conditions the input power (when using the external power supply).

Training Manual STAR TRAC FITNESS 17 of 22 637-1376 Rev: A 3. Other Electrical Components A. Power/Line Filter – Conditions the input power (when using the external power supply).

Page 18 - a. External Power Supply Port; communicate with the unit.; c. Coax Cable Connector –; embedded touch screen.

Training Manual STAR TRAC FITNESS 18 of 22 637-1376 Rev: A B. External Power/CSAFE/Coax Cable Connector a. External Power Supply Port – Is needed when the unit has a PVS or embedded touch screen installed. b. CSAFE Port – This is where the RJ45 cable needs to be plugged in to make external equipment...

Page 21 - C. Transmission Chain; – Connects the pedal drive to the main drive.

Training Manual STAR TRAC FITNESS 21 of 22 637-1376 Rev: A C. Transmission Chain – Connects the pedal drive to the main drive.

Page 22 - Alternator and Drive Belt; Connects the alternator to the main drive.

Training Manual STAR TRAC FITNESS 22 of 22 637-1376 Rev: A D. Alternator and Drive Belt a. Alternator Belt – Connects the alternator to the main drive. b. Drive Belt – Connects the lower pulley to the main pulley.