Smeg SHI410X1 - Manuals - manualsarea.com

Page 2 - INDEX; EN

2 2 INDEX SAFETY INFORMATION ......................................................................................................................................................... 3 CHARACTERISTICS ......................................................................................................

Page 3 - SAFETY INFORMATION; The wire connection has to be done by specialized technician.

EN 3 3 SAFETY INFORMATION For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance. The wire ...

Page 4 - supplied with; Failure to install the screws or fixing device in accordance

EN 4 4 • If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. When the cooker hood is used in conjunction with appliances supplied with ene...

Page 6 - CHARACTERISTICS; Components

EN 6 6 CHARACTERISTICS Components Ref. Q.ty Product Components 1 1 Hood Body, complete with: Controls, Light, Blower, Filters 2 1 Chimney Upper 7.1 1 Telescopic frame complete with extractor, consisting of: 7.1a 1 Upper frame 7.1b 1 Lower frame 9 1 Reducer Flange ø 150-120 mm 10 1 Flange ø 120 mm 11...

Page 7 - Dimensions

EN 7 7 Dimensions 650mm 600mm * Dimensions of the hood in ducting version. ** Dimensions of the hood in recycling version.

Page 8 - INSTALLATION; Drilling the Ceiling/shelf and fixing the frame; DRILLING THE CEILING/SHELF

EN 8 8 INSTALLATION Drilling the Ceiling/shelf and fixing the frame DRILLING THE CEILING/SHELF • Use a plumb line to mark the centre of the hob on the ceiling/support shelf. • Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template is in the correct positi...

Page 9 - PREPARATION OF THE FRAME FOR THE HOOD IN

EN 9 9 PREPARATION OF THE FRAME FOR THE HOOD IN RECYCLING VERSION In case the hood is used in recycling version it is necessary to prepare the frame with all the necessary connection pieces. In order to make the installation easier it is necessary to lengthen the frame: • Unscrew the two screws 2.1 ...

Page 10 - FIXING THE FRAME; Connections; AIR OUTLET DUCTING VERSION

EN 10 10 FIXING THE FRAME • Lift the frame up, making sure that the index over the frame plate is turned forwards. • Fit the frame slots onto the two screws inserted in the ceiling as above, and turn until reaching the centre of theadjustment slot. • Tighten the two screws and fasten the other two s...

Page 11 - Installing of the chimney and fixing of the hood; ELECTRICAL CONNECTION

EN 11 11 Installing of the chimney and fixing of the hood When the hood is installed in recycling version the chimney has to be positioned with the slots upwards. When the hood is in-stalled in ducting version it has to be positioned in the opposite way. • Place the chimney on the frame and fix it t...

Page 12 - USE; Control panel

EN 12 12 USE L L1 T1 T2 T3 T4 L2 L3 L4 Control panel Button Function Led L Turns the lighting system on and off. - Press and hold for approx. 2 seconds to turn the lighting system on and off at reduced intensity. - T1 Turn the suction motor on and off at speed one. On. Press and hold the button for ...

Page 13 - CARE AND CLEANING; Metal grease filters; Resetting the alarm signal; Cleaning the Filters

EN 13 13 CARE AND CLEANING Metal grease filters These can also be washed in the dishwasher, and need to be cleaned when all the command LEDs light up in a continuous manner or at least once every 2 months use, or more frequently if use is particularly intensive. Resetting the alarm signal • Press bu...

Page 14 - Activating the alarm signal; Lighting unit

EN 14 14 Activated Charcoal Filter (Recirculation Version) • This cannot be washed or regenerated, and must be changed when all the command LEDs start to flash, or at least once every 4 months. Activating the alarm signal • In Recirculation Version Hoods, the Filter Saturation Alarm must be activate...