Smart 600i6 - Manuals

vii smarttech.com/kb/170585 Contents Important information i Safety warnings, cautions and important information i Environmental requirements iv Chapter 1: About your interactive whiteboard system 1 SMART Board 600i6 interactive whiteboard system features 2 Included accessories 4 Chapter 2: Installi...

Chapter 1 1 smarttech.com/kb/170585 Chapter 1: About your interactivewhiteboard system SMART Board 600i6 interactive whiteboard system features 2 SMART Board 600 series interactive whiteboard 2 SMART UF70 or SMART UF70w projector 3 Extended Control Panel (ECP) 4 Included accessories 4 Remote control...

C H A P T E R 1 About your interactive whiteboard system 3 smarttech.com/kb/170585 For more information about your SMART Board interactive whiteboard, see the SMART Board 600 and D600 series interactive whiteboard installation and user’s guide ( smarttech.com/kb/001414 ). SMART UF70 or SMART UF70w p...

C H A P T E R 1 About your interactive whiteboard system 4 smarttech.com/kb/170585 Extended Control Panel (ECP) Your projector system’s ECP attaches to the bottom frame of your interactive whiteboard. The ECP features controls for power, source selection and volume adjustment, as well as an integrat...

C H A P T E R 1 About your interactive whiteboard system 5 smarttech.com/kb/170585 N O T E Some of SMART’s older pens aren’t designed to reflect infrared light and the pen tray sensors might not detect them reliably. T I P Wrap light-colored tape around a substitute pen to improve the reflection of ...

Chapter 2 7 smarttech.com/kb/170585 Chapter 2: Installing your interactivewhiteboard system Choosing a location 8 Choosing a height 8 Securing your interactive whiteboard system 8 Locking the pen tray to your interactive whiteboard 8 Securing the projector to the boom 8 Routing the cables 9 Installi...

C H A P T E R 2 Installing your interactive whiteboard system 8 smarttech.com/kb/170585 Choosing a location Choose a location for your interactive whiteboard system that’s far from bright light sources, such as windows and strong overhead lighting. Bright light sources can cause distracting shadows ...

C H A P T E R 2 Installing your interactive whiteboard system 9 smarttech.com/kb/170585 Routing the cables When connecting cables from your SMART UF70 projector to your interactive whiteboard system, make sure that all cables pass along the top of the interactive whiteboard wall-mounting bracket and...

C H A P T E R 2 Installing your interactive whiteboard system 10 smarttech.com/kb/170585 Installing SMART software You must install SMART software, such as SMART Meeting Pro™ software or SMART Notebook™ collaborative learning software on the computer connected to your interactive whiteboard system t...

Chapter 3 11 smarttech.com/kb/170585 Chapter 3: Using your interactivewhiteboard system Using your projector 11 Using your remote control 11 Replacing the remote control battery 12 Using the remote control buttons 13 Adjusting projector settings 14 Focusing the image 20 Adjusting the image 21 Projec...

C H A P T E R 3 Using your interactive whiteboard system 20 smarttech.com/kb/170585 Setting Use Notes Resolution Displays the projector’s mostrecently detected video sourcesignal resolution and refreshrate. If there is no current video input source signal,this setting displays the last known sources...

C H A P T E R 3 Using your interactive whiteboard system 21 smarttech.com/kb/170585 Adjusting the image Refer to these notes when adjusting the projected image as described in the included SMART Board 660i6,680i6, 685i6 and 690i6 interactive whiteboard system installation guide ( smarttech.com/kb/17...

C H A P T E R 3 Using your interactive whiteboard system 23 smarttech.com/kb/170585 N O T E S l To connect your interactive whiteboard, see the SMART Board 660i6,680i6, 685i6 and 690i6 interactive whiteboard system installation guide ( smarttech.com/kb/170498 ). l To connect accessories to your inte...

Chapter 4 27 smarttech.com/kb/170585 Appendix 4: Integrating other devices Video format compatibility 27 Native video format 27 Video format compatibility 28 SMART UF70 projector 28 SMART UF70w projector 29 HD and SD signal format compatibility 31 SMART UF70 projector 31 SMART UF70w projector 31 Vid...

C H A P T E R 4 Integrating other devices 31 smarttech.com/kb/170585 HD and SD signal format compatibility The following tables list the projectors’ high definition (HD) and standard definition (SD) format signal compatibility, which the projector adjusts automatically when you use the aspect ratio ...

C H A P T E R 4 Integrating other devices 32 smarttech.com/kb/170585 N O T E Your projector is HD Ready. Its native resolution supports a pixel-perfect display of 720p source content. However, because the projector compresses 1080p source content to fit its native resolution, it doesn’t support a pi...

C H A P T E R 4 Integrating other devices 33 smarttech.com/kb/170585 Connecting peripheral sources and outputs Follow these instructions if you have a peripheral device to connect to your interactive whiteboard system, such as a DVD/Blu-ray player or a USB device. N O T E S l Measure the distance be...

C H A P T E R 5 Maintaining your interactive whiteboard system 36 smarttech.com/kb/170585 l Before you clean the projector, press the Power button twice on the ECP or remote control to put the system in Standby mode, and then allow the lamp to cool for at least 30 minutes. l Do not spray cleaners, s...

C H A P T E R 5 Maintaining your interactive whiteboard system 37 smarttech.com/kb/170585 Replacing the projector lamp This section provides instructions for replacing the projector lamp module. Removing and replacing the projector lamp module Eventually the lamp will dim and a message will appear r...

C H A P T E R 5 Maintaining your interactive whiteboard system 40 smarttech.com/kb/170585 4. Replace the lamp cover. 5. Connect the power cable to the wall outlet. 6. Press the Power button once on the remote control or ECP to confirm that the projector is operating and that the lamp module is corre...

Chapter 6 43 smarttech.com/kb/170585 Chapter 6: Troubleshooting your interactivewhiteboard system Before you start 44 Locating status lights 44 Locating serial numbers 45 Determining your interactive whiteboard system’s status 45 Resolving interactive whiteboard issues 47 Resolving operation issues ...

C H A P T E R 6 Troubleshooting your interactive whiteboard system 44 smarttech.com/kb/170585 This chapter provides basic troubleshooting information for your interactive whiteboard system. For issues not covered in this chapter, consult the SMART Support website ( smarttech.com/support ) or contact...

C H A P T E R 6 Troubleshooting your interactive whiteboard system 45 smarttech.com/kb/170585 Locating serial numbers The serial number on your SMART Board 600 series interactive whiteboard is located on the lower- right edge of the interactive whiteboard’s frame. For more information, see the SMART...

C H A P T E R 6 Troubleshooting your interactive whiteboard system 47 smarttech.com/kb/170585 ProjectorPower light ProjectorService light ECP light InteractivewhiteboardReady light Projectedimage Touch andpen control Status and relatedtroubleshooting Off Off Off Off None None The projector power cab...

C H A P T E R 6 Troubleshooting your interactive whiteboard system 48 smarttech.com/kb/170585 l Confirm that the USB cable is properly connected from a fully functional USB port on the computer to the correct USB port on the ECP. l Confirm that the projector’s on-screen menu option for the USB sourc...

C H A P T E R 6 Troubleshooting your interactive whiteboard system 52 smarttech.com/kb/170585 Unaligned projected image Alignment errors occur when the projected image isn’t perpendicular to the screen. Alignment errors can occur when you mount your interactive whiteboard system on an uneven surface...

C H A P T E R 6 Troubleshooting your interactive whiteboard system 53 smarttech.com/kb/170585 3. Check the ECP’s volume knob or use the projector’s remote control to ensure that the volume isn’t at the lowest setting. 4. Ensure that your speaker or audio system is on and that the volume is turned up...

C H A P T E R 6 Troubleshooting your interactive whiteboard system 54 smarttech.com/kb/170585 Accessing the service menu C A U T I O N l To prevent tampering or unintentional changes, only system administrators should access the service menu. Do not share the service menu access code with casual use...

C H A P T E R 6 Troubleshooting your interactive whiteboard system 55 smarttech.com/kb/170585 Resetting the projector At some point during troubleshooting, you might need to reset all projector settings. I M P O R T A N T This action is irreversible. To reset all projector settings 1. Using the remo...

A P P E N D I X A Remotely managing your system through a network interface 58 smarttech.com/kb/170585 Accessing web page management Before you can access the web page, connect your projector to the network, and then enable the projector’s network functions using the projector’s menu. An IP address ...

A P P E N D I X A Remotely managing your system through a network interface 62 smarttech.com/kb/170585 Submenu setting Description HDMI Assigns an alternative name to your HDMI input, which appearswhen you select the HDMI input. Emergency Alert Turns the on-screen alert broadcast message on or off. ...

A P P E N D I X A Remotely managing your system through a network interface 65 smarttech.com/kb/170585 l If you forget the projector password, refer to Accessing the service menu on page 54 to set the projector setting to factory defaults. Simple Network Management Protocol (SNMP) Your projector sup...

Appendix B 67 smarttech.com/kb/170585 Appendix B: Remotely managing your systemthrough an RS-232 serialinterface Connecting your room control system to the SMART UF70 projector 68 Pin configuration on the projector’s RS-232 connector 68 Serial interface settings 68 Projector programming commands 70 ...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 68 smarttech.com/kb/170585 Connecting your room control system to theSMART UF70 projector By connecting a computer or room control system to the RS-232 serial interface of the SMART UF70 projector, you can select vide...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 70 smarttech.com/kb/170585 Projector programming commands This section documents the projector programming commands and responses. Power state controls These commands put the projector in and out of Standby mode and r...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 73 smarttech.com/kb/170585 Video Control Video output related controls. The range of values used for these commands should match the range displayed visually on the OSD. The firmware must handle videofreeze and videom...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 78 smarttech.com/kb/170585 >set brightness-15 brightness=55 > All video commands should also have an optional source specification. >set brightness = 65 brightness=65 This sets the brightness of the specified...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 81 smarttech.com/kb/170585 Network information Various network information. Command/response definitions Command Response Powered off get netstatus netstatus =[current] yes set network network=[current] yes get networ...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 83 smarttech.com/kb/170585 System Information Various system information. Command/response definitions Command Response Powered off set autosignal [target] autosignal =[current] no get autosignal autosignal =[current]...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 90 smarttech.com/kb/170585 Service Information These are commands used in servicing and manufacturing of the unit. They should be hidden from the user during normal operation. Command/response definitions Command Resp...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 91 smarttech.com/kb/170585 Field Definitions Field Possible Values Description current displayhour l 0 ~ 20000 Current Display hours. target testpattern l = ? Set the test pattern to pattern number X (1~4). If only on...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 93 smarttech.com/kb/170585 Engineering commands These commands are to be part of the RS232 list but not viewable by the “?” command Command/response definitions Command Response Powered off set dbmsgon [target] dbmsgo...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 95 smarttech.com/kb/170585 Additional commands These commands & behaviors are to provide backward compatibility for legacy control interfaces. Command/response definitions Command Execute command: Behaviour set in...

A P P E N D I X B Remotely managing your system through an RS-232 serial interface 96 smarttech.com/kb/170585 Unknown command If an unknown command is received, the projector must identify this to the user. This is accomplished by sending the following response back to the user. Please note that the...

Appendix C 97 smarttech.com/kb/170585 Appendix C: Disabling user USB access In some situations, you might want to disable the ECP’s front USB receptacle. Disabling the USB receptacle prevents users from using or saving documents to USB drives using the ECP’s front USB receptacle. The other USB recep...

Appendix D 101 smarttech.com/kb/170585 Appendix D: Remote control code definitions IR signal format: NEC1 Key Repeatformat Vendor code Key code Byte 1 Byte 2 Byte 3 Byte 4 Input F1 8B CA 14 EB Power ( ) F1 8B CA 12 ED Menu F1 8B CA 1B E4 Up ( ) F1 8B CA 40 BF Left ( ) F1 8B CA 42 BD Enter ( ) F1 8B ...

Appendix E 103 smarttech.com/kb/170585 Appendix E: Hardware environmentalcompliance SMART Technologies supports global efforts to ensure that electronic equipment is manufactured, sold and disposed of in a safe and environmentally friendly manner. Waste Electrical and Electronic Equipment andBattery...

Index 105 smarttech.com/kb/170585 3 3.5 mm audio connectors 22 A accessories included 4 alarms 62 aspect ratios 27-28, 31-32, 61 Aspect ratios 17 audio connections for 22 controlling volume of 24, 59 muting 13 resolving issues with 52 B batteries 12, 103 C closed captioning 59 composite video connec...