National Instruments Smart Camera - Manuals

Page 2 - What You Need to Get Started; Building a Custom Power Cable; Safety Information; Caution

NI Smart Camera I/O Accessory User Guide 2 ni.com What You Need to Get Started ❑ NI Smart Camera I/O Accessory kit, which includes the accessory, 15-pin D-SUB female to 15-pin D-SUB male cable, 2 m (part number 197817-02), and two-position header connector (Wago part number 734-102, available from w...

Page 3 - must

© National Instruments Corporation 3 NI Smart Camera I/O Accessory User Guide Operate the device only at or below Pollution Degree 2. Pollution is foreign matter in a solid, liquid, or gaseous state that can reduce dielectric strength or surface resistivity. The following is a description of polluti...

Page 4 - Installation; Note; Connect the Camera Cable; Option B: Using a Custom Two-Position Power Cable; Building a Two-Position Power Cable

NI Smart Camera I/O Accessory User Guide 4 ni.com Installation To get started with the NI 17xx Smart Camera I/O Accessory, complete the following steps while referring to Figure 1. If you have not already installed the NI Smart Camera and required software, refer to Getting Started with the NI 17xx ...

Page 5 - Apply Power; Fuses; Leave all other pins unconnected.; Do; the wires from wear due to vibration and strain.

© National Instruments Corporation 5 NI Smart Camera I/O Accessory User Guide Apply Power When power is first applied to the smart camera, the POWER LED flashes red for one second while internal systems power up. The POWER LED then lights green when power is correctly wired to the smart camera. If t...

Page 6 - Power Two-Position Header Wiring Diagram; Testing Fuses; Replacing Fuses; COM

NI Smart Camera I/O Accessory User Guide 6 ni.com 2. Wire the voltage output of the 24 VDC +20%/–15% (IEC 1311) power supply to the main voltage input on the two-position connector as shown in Figure 3. Insert a small flathead screwdriver into the square opening. Using the screwdriver as a lever to ...

Page 7 - Removing the Circuit Board; Fuse

© National Instruments Corporation 7 NI Smart Camera I/O Accessory User Guide Replacing Fuses To replace a blown fuse on the accessory, complete the following steps. 1. Unplug the accessory power. 2. Remove all signal wires and cables from the accessory. 3. Unscrew the two screws from a side panel w...

Page 8 - Specifications; Refer to the; Power Requirement; The NI Smart Camera I/O Accessory is intended for indoor use only.; Safety; certification; Certification column.

NI Smart Camera I/O Accessory User Guide 8 ni.com Specifications This section lists the specifications of the NI Smart Camera I/O Accessory. These specifications are typical at 25 °C, unless otherwise noted. Note Refer to the NI 17xx Smart Camera User Manual for specifications about signals. Power R...

Page 9 - CE Compliance; Compliance with EU Directives; Environmental Management; NI and the Environment; Waste Electrical and Electronic Equipment (WEEE); EU Customers; ⬉ᄤֵᙃѻક∵ᵻ᥻ࠊᄣ⧚ࡲ⊩ ˄Ё೑; RoHS; Ё೑ᅶ᠋; National Instruments; (For information about China RoHS compliance, go to

© National Instruments Corporation 9 NI Smart Camera I/O Accessory User Guide CE Compliance The NI Smart Camera I/O Accessory meets the essential requirements of applicable European Directives, as amended for CE marking, as follows: • 2006/95/EC; Low-Voltage Directive (safety) • 2004/108/EC; Electro...

Page 10 - Where to Go for Support; . If your product supports calibration, you can obtain the

NI Smart Camera I/O Accessory User Guide 10 ni.com Where to Go for Support The National Instruments Web site is your complete resource for technical support. At ni.com/support you have access to everything from troubleshooting and application development self-help resources to email and phone assist...