National Instruments USB-6008/6009 - Manual
National Instruments USB-6008/6009 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Safety Guidelines; Caution
- Page 3 – Operate the device at or below the Measurement Category I
- Page 4 – Software; USB Devices Getting Started Guide; Start»All Programs»National Instruments»; for more information.; VI Logger; Start»All Programs»
- Page 5 – Hardware
- Page 6 – Setting Up Hardware; Complete the following steps to set up the hardware:; Note
- Page 7 – Module
- Page 8 – GND
- Page 10 – Analog Input; MUX
- Page 11 – AI FIFO
- Page 12 – Connecting Reference Single-Ended Voltage Signals
- Page 13 – Digital Trigger; Analog Output; DACs
- Page 14 – Connecting Analog Output Loads; Minimizing Glitches on the Output Signal; for more information about minimizing; Digital I/O Circuitry
- Page 15 – Source/Sink Information; for more information about how to
- Page 16 – Place an ammeter in series with the load.
- Page 17 – Static DIO; Event Counter; Specifications; Reference and Power Sources
- Page 18 – software selectable
- Page 19 – trigger
- Page 21 – Digital logic levels; External Voltage; to 5 V; Bus Interface; Level
- Page 23 – Voltages; Connect only voltages that are within these limits.; Hazardous Locations; The USB-6008/6009 are not certified for use in hazardous locations.; Environmental
- Page 24 – Electromagnetic Compatibility; FCC Part 15A above 1 GHz; CE Compliance; Where to Go for Support; you have access to everything from
- Page 25 – and follow the calling
USER GUIDE AND SPECIFICATIONS
USB-6008/6009
This guide describes how to use the National Instruments USB-6008/6009
data acquisition (DAQ) devices and lists specifications.
Introduction
The NI USB-6008/6009 provides connection to eight analog input (AI)
channels, two analog output (AO) channels, 12 digital input/output (DIO)
channels, and a 32-bit counter with a full-speed USB interface.
Note
This manual revision updates naming conventions to reflect the conventions used in
NI-DAQmx. Table 1 notes the correlation between the old and updated names.
Table 1.
Digital Output Driver Type Naming Conventions
Hardware Functionality
NI-DAQmx Terminology
Open-drain
Open collector
Push-pull
Active drive
Table 2.
Differences Between the USB-6008 and USB-6009
Feature
USB-6008
USB-6009
AI Resolution
12 bits differential,
11 bits single-ended
14 bits differential,
13 bits single-ended
Maximum AI Sample Rate,
Single Channel
*
10 kS/s
48 kS/s
Maximum AI Sample Rate,
Multiple Channels (Aggregate)
*
10 kS/s
42 kS/s
DIO Configuration
Open collector
Open collector or active drive
*
Might be system dependent.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
USB-6008/6009 User Guide and Specifications 2 ni.com Figure 1. USB-6008/6009 Figure 2. USB-6008/6009 Back View Safety Guidelines Caution Operate the hardware only as described in these operating instructions. The following section contains important safety information that you must follow when insta...
© National Instruments Corporation 3 USB-6008/6009 User Guide and Specifications Do not operate the device in an explosive atmosphere or where there may be flammable gases or fumes. If you must operate the device in such an environment, it must be in a suitably rated enclosure. If you need to clean ...
USB-6008/6009 User Guide and Specifications 4 ni.com • Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a standard wall outlet (for example...
