National Instruments SCC-AI01 - Manual
National Instruments SCC-AI01 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Conventions; Read Me First: Safety and Radio-Frequency; bold; italic; What You Need to Get Started; XX
- Page 3 – Scaling Voltage Measurements; Unpacking the Module; Never
- Page 4 – Installing the Module; Connecting the Input Signals
- Page 6 – resistor. Figure 1-4 shows a floating signal connection
- Page 7 – Configuring the SCC System; Open; Measurement & Automation; and select; Create New; Under; NI-DAQmx SCC Connector Block; select; Finish
- Page 9 – Virtual Channels, Physical Channels, and Tasks
- Page 10 – Creating a Virtual Channel in Traditional NI-DAQ
- Page 11 – If you configured the SCC-AI; Specifications; These ratings are typical at 25 °C unless otherwise stated.; Input Characteristics; Input impedance
- Page 12 – Filter Characteristics
- Page 13 – Environmental; Electromagnetic Compatibility; must; CE Compliance
- Page 14 – Calibrating Gain and Offset Errors; Module
- Page 16 – Module Pin Assignments; Pin Number
- Page 17 – GND
USER GUIDE
SCC-AI Series Isolated Analog
Input Modules
The SCC-AI Series isolated analog input modules (SCC-AI
XX
) can extract
a relatively low-amplitude input signal from a high-common-mode voltage
so the E Series DAQ device can measure the input signal. They also can
amplify and filter the input signal, resulting in higher measurement
resolution and accuracy.
SCC-AI
XX
modules are available in a range of gains from 0.2 to 200. They
contain lowpass filters of either 10 kHz or 4 Hz bandwidth. Table 1-1 gives
the gain and bandwidth for each module.
Table 1-1.
SCC-AI
XX
Module Input/Output Range, Gain, and Bandwidth
Model
Input Range
Output Range
Gain
Bandwidth
SCC-AI01
±
42 V
±
8.4 V
0.2
10 kHz
SCC-AI02
±
20 V
±
10 V
0.5
10 kHz
SCC-AI03
±
10 V
±
10 V
1
10 kHz
SCC-AI04
±
5 V
±
10 V
2
10 kHz
SCC-AI05
±
1 V
±
10 V
10
10 kHz
SCC-AI06
±
100 mV
±
10 V
100
10 kHz
SCC-AI07
±
50 mV
±
10 V
200
10 kHz
SCC-AI13
±
10 V
±
10 V
1
4 Hz
SCC-AI14
±
5 V
±
10 V
2
4 Hz
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
SCC-AI Series Isolated Analog Input Modules 2 ni.com Conventions The following conventions are used in this guide: < > Angle brackets that contain numbers separated by an ellipsis represent a range of values associated with a bit or signal name—for example, ai<0..7>. This icon denotes a ...
© National Instruments Corporation 3 SCC-AI Series Isolated Analog Input Modules ❑ One or more SCC-SG XX ❑ SCC-SG Series Strain-Gauge Modules User Guide ❑ SC-2345 User Manual ❑ Read Me First: Safety and Radio-Frequency Interference ❑ SC-2345 Quick Reference Label ❑ 68-pin Basic or E Series DAQ devic...
SCC-AI Series Isolated Analog Input Modules 4 ni.com Installing the Module Caution Refer to the Read Me First: Safety and Radio-Frequency Interference document before removing equipment covers or connecting/disconnecting any signal wires A blue label stripe identifies the SCC-AI XX as an analog inpu...
