National Instruments SCC-LP04 - Manual
National Instruments SCC-LP04 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – bold; italic; SCC
- Page 3 – What You Need to Get Started; XX; Using the SCC-LPXX when Scaling Voltage Measurements
- Page 4 – Device Specific Information; Installing the Module; Connecting the Input Signals
- Page 5 – The signal source can be floating or ground-referenced. The SCC-LP; For information about configuring the SCC-LP
- Page 6 – when Scaling Voltage Measurements; Specifications; Amplifier Characteristics
- Page 7 – Filter Characteristics; Input Signal
- Page 8 – Stability; Analog power; Physical; 5 V, Installation Category I; Environmental
- Page 9 – Safety; Electromagnetic Compatibility; CE Compliance
- Page 10 – Theory of Operation; Performance
- Page 14 – Figure 6a shows that the SCC-LP
- Page 15 – as an Antialiasing Filter; Nyquist frequency
- Page 16 – Calibrating Gain Errors
- Page 17 – Module Pin Assignments; Figure 8 shows the I/O connector pins on the bottom of the module.
- Page 18 – Device Specific; Pin Number
USER GUIDE
SCC-LP Series Lowpass Filter
Modules
The SCC-LP Series lowpass filter modules contain fourth-order
Butterworth filter circuitry. They accept two differential input signals
within a
±
10 V range. A differential amplifier attenuates each signal by
a factor of two. The output of the amplifier passes through a fourth-order
Butterworth filter circuit.
The SCC-LP Series consists of the following modules:
•
SCC-LP01—25 Hz cutoff frequency
•
SCC-LP02—50 Hz cutoff frequency
•
SCC-LP03—150 Hz cutoff frequency
•
SCC-LP04—1 kHz cutoff frequency
Conventions
The following conventions are used in this guide:
< >
Angle brackets that contain numbers separated by an ellipsis represent
a range of values associated with a bit or signal name—for example,
P0.<3..0>.
»
The
»
symbol leads you through nested menu items and dialog box options
to a final action. The sequence
File»Page Setup»Options
directs you to
pull down the
File
menu, select the
Page Setup
item, and select
Options
from the last dialog box.
This icon denotes a note, which alerts you to important information.
This icon denotes a caution, which advises you of precautions to take to
avoid injury, data loss, or a system crash. When this symbol is marked on
the product, refer to the
Read Me First: Safety and Radio-Frequency
Interference
document, shipped with the product, for precautions to take.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
SCC-LP Series Lowpass Filter Modules User Guide 2 ni.com When symbol is marked on a product, it denotes a warning advising you to take precautions to avoid electrical shock. When symbol is marked on a product, it denotes a component that may be hot. Touching this component may result in bodily injur...
© National Instruments Corporation 3 SCC-LP Series Lowpass Filter Modules User Guide What You Need to Get Started To set up and use the SCC-LP XX , you need the following items: ❑ SC-2345/2350 with one of the following: – SCC-PWR01 – SCC-PWR02 and the PS01 power supply – SCC-PWR03—requires a 7 to 42...
SCC-LP Series Lowpass Filter Modules User Guide 4 ni.com Device Specific Information Note For general SCC module installation and signal connection information, and information about the SC-2350 carrier, refer to the SCC Quick Start Guide , available for download at ni.com/manuals . Installing the M...
