National Instruments SCXI -1122 - Manual

National Instruments SCXI -1122

National Instruments SCXI -1122 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
Page: / 62

Table of Contents:

  • Page 3 – Warranty; Copyright
  • Page 4 – WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS
  • Page 5 – Contents; About This Manual; ix
  • Page 6 – Glossary
  • Page 7 – Figures
  • Page 8 – Organization of This Manual; The SCXI-1122 User Manual is organized as follows:
  • Page 9 – Conventions Used in This Manual; bold italic
  • Page 10 – The National Instruments Documentation Set; you should not need the register-level programmer manual. Using
  • Page 11 – Customer Communication
  • Page 12 – What Your Kit Should Contain; Kit Component
  • Page 13 – Software Programming Choices; LabVIEW and LabWindows Application Software; Software; LabVIEW for Windows; NI-DAQ Driver Software
  • Page 14 – Figure 1-1. The Relationship between the Programming Environment,
  • Page 15 – Register-Level Programming; Optional Equipment; Equipment; SCXI-1322 front terminal block
  • Page 16 – Custom Cables; Unpacking; Never touch the exposed pins of connectors.
  • Page 17 – Module Configuration
  • Page 19 – Digital Signal Connections; jumper W2 is irrelevant.; Jumper; pullup resistor to; Analog Configuration
  • Page 20 – reference mode
  • Page 21 – Input Channel; –This unit should only be opened by qualified personnel aware of
  • Page 22 – Hardware Installation; your cable installation guide.
  • Page 24 – resulting from incorrect signal connections.
  • Page 25 – Front Connector
  • Page 26 – Front Signal Connection Descriptions; Pin; No Connect–Do not connect any signal to these pins.
  • Page 27 – Analog Input Channel Signal Connections
  • Page 28 – Figure 3-4. Floating AC-Coupled Signal Connection Referenced
  • Page 30 – Single -Sample Channel Scanning; Excitation Channel Signal Connections; liable for any damages or injuries resulting from such signal
  • Page 31 – Table 3-1. Maximum Load per Excitation Channel; Excitation Level; Using the Internal Half-Bridge Completion; Figure 3-7. Connecting a Quarter-Bridge Strain Gauge to Channel 0; Temperature Sensor Connection; liable for any damages resulting from such signal connections.
  • Page 32 – Rear Signal Connector
  • Page 33 – Rear Signal Connection Descriptions
  • Page 34 – Digital I/O Signal Connections; tied to the module digital ground.
  • Page 35 – SCXIbus Line
  • Page 36 – Functional Overview
  • Page 38 – Rear Signal Connector, SCXIbus Connector, and SCXIbus Interface; Analog Input Channels
  • Page 39 – Sense
  • Page 40 – Excitation Output Channels
  • Page 41 – . If you connect loads greater than 5 k
  • Page 42 – Type
  • Page 43 – Overview; Calibration Equipment Requirements; Accuracy
  • Page 44 – Gain and Offset Calibration
  • Page 45 – to the amplifier input.; units as given by the following formula:; function or VI as described in your software user manual.
  • Page 46 – Excitation Calibration; excitation errors do not exceed the ranges listed in Table 5-1.; Error Type
  • Page 47 – C unless; Analog Input; Module Gain Max; Overvoltage protection 250 Vrms powered on, 250 V powered off
  • Page 48 – Filter Bandwidth
  • Page 49 – Excitation
  • Page 50 – Branch Offices
  • Page 51 – Technical Support Form
  • Page 52 – SCXI-1122 Hardware Configuration Form
  • Page 54 – Documentation Comment Form
  • Page 55 – Prefix
  • Page 59 – Index; Numbers
  • Page 62 – floating signal connection referenced
Loading the manual

© Copyright 1993, 1999 National Instruments Corporation.

All Rights Reserved.

User Manual

Sixteen-Channel Isolated Transducer Multiplexer Module for Signal

Conditioning

September 1999 Edition

Part Number 320516B-01

SCXI -1122

TM

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Warranty; Copyright

Warranty The SCXI-1122 is warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace equipment that proves to be defective during the warranty ...

Page 4 - WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS

WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS (1) NATIONAL INSTRUMENTS PRODUCTS ARE NOT DESIGNED WITH COMPONENTS AND TESTING FOR A LEVEL OF RELIABILITY SUITABLE FOR USE IN OR IN CONNECTION WITH SURGICAL IMPLANTS OR AS CRITICAL COMPONENTS IN ANY LIFE SUPPORT SYSTEMS WHOSE FAILURE TO PERFORM ...

Page 5 - Contents; About This Manual; ix

© National Instruments Corporation v SCXI-1122 User Manual Contents About This Manual ............................................................................................................. ix Organization of This Manual ............................................................................

Other National Instruments Models

All National Instruments Other