National Instruments SC-2040 - Manual

National Instruments SC-2040

National Instruments SC-2040 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
Page: / 56

Table of Contents:

  • Page 5 – Contents; About This Manual
  • Page 6 – Glossary
  • Page 7 – Figures
  • Page 8 – Organization of This Manual; The SC-2040 User Manual is organized as follows:
  • Page 9 – Conventions Used in This Manual; The following conventions are used in this manual:; The National Instruments Documentation Set; manual sets and the NI-DAQ manuals. After you set up your hardware
  • Page 10 – Related Documentation; Your DAQ hardware user manual; Customer Communication
  • Page 11 – What You Need to Get Started
  • Page 12 – Software Programming Choices; LabVIEW and LabWindows Application Software
  • Page 13 – Figure 1-1. The Relationship between the Programming Environment,
  • Page 14 – Register-Level Programming; Optional Equipment; Single or double height rack-mount kit with acrylic plastic cover; Unpacking; Never touch the exposed pins of connectors.
  • Page 15 – Board Configuration
  • Page 17 – Switch
  • Page 18 – Table 2-3. DAQ Board Ground Isolation Selection
  • Page 19 – resistor is
  • Page 20 – Supplementary Configuration Information; Power Supply Selection; Gain Selection; Table 2-6. Gain Switches for Each Channel; Channel
  • Page 21 – Desired Gain; Input Mode Selection
  • Page 22 – Installation
  • Page 23 – I/O Connector Pin Description
  • Page 25 – Table 3-1. Pin Assignments for Connectors J11 and J12
  • Page 26 – Signal Connection Description; Table 3-2. Input Connectors Signal Summary
  • Page 29 – Analog Signal Inputs; Figure 3-3 illustrates how to connect a ground-referenced signal.
  • Page 30 – Figure 3-4 illustrates how to connect a floating signal.; When you use a 1 M
  • Page 32 – liable for; G V
  • Page 33 – where V; Digital Signal Inputs; series with the signal source will minimize reflection.; Monitoring Signal Outputs; Other Connection Considerations
  • Page 34 – Functional Overview
  • Page 36 – Analog Circuitry; Input Protection; 5 V powered off and; Amplification
  • Page 37 – Triggering from the DAQ Board
  • Page 38 – External Triggering
  • Page 39 – Output Connection; 5 V source, which is used to power the analog circuitry. A
  • Page 40 – Software Calibration; Offset Adjustment
  • Page 41 – Gain Adjustment; Hardware Calibration
  • Page 42 – Table 5-1. Calibration Component Identification; To calibrate the SC-2040 board, the following steps are required:
  • Page 43 – until the output is close to zero.
  • Page 44 – Analog Input; Input Characteristics
  • Page 45 – Amplifier Characteristics; Dynamic Characteristics
  • Page 46 – Stability; Power Requirement
  • Page 47 – Branch Offices
  • Page 48 – Technical Support Form
  • Page 50 – Documentation Comment Form
  • Page 51 – Prefix
  • Page 53 – Index
  • Page 54 – See calibration procedures.
  • Page 56 – specifications
Loading the manual

© Copyright 1994 National Instruments Corporation.

All Rights Reserved.

SC-2040

User Manual

Eight-Channel Simultaneous Sample-and-Hold Accessory

September 1994 Edition

Part Number 371191A-01

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 5 - Contents; About This Manual

© National Instruments Corporation v SC-2040 User Manual Contents About This Manual ................................................................................................................ ix Organization of This Manual ...........................................................................

Page 6 - Glossary

Contents SC-2040 User Manual vi © National Instruments Corporation Chapter 4Theory of Operation .......................................................................................................... 4-1 Functional Overview.............................................................................

Page 7 - Figures

Contents © National Instruments Corporation vii SC-2040 User Manual Figures Figure 1-1. The Relationship between the Programming Environment,NI-DAQ, and Your Hardware ............................................................................. 1-3 Figure 2-1. SC-2040 Parts Locator Diagram.............

Other National Instruments Models

All National Instruments Other