National Instruments Smart Camera - Manual
National Instruments Smart Camera – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – What You Need to Get Started; Building a Custom Power Cable; Safety Information; Caution
- Page 3 – must
- Page 4 – Installation; Note; Connect the Camera Cable; Option B: Using a Custom Two-Position Power Cable; Building a Two-Position Power Cable
- Page 5 – Apply Power; Fuses; Leave all other pins unconnected.; Do; the wires from wear due to vibration and strain.
- Page 6 – Power Two-Position Header Wiring Diagram; Testing Fuses; Replacing Fuses; COM
- Page 7 – Removing the Circuit Board; Fuse
- Page 8 – Specifications; Refer to the; Power Requirement; The NI Smart Camera I/O Accessory is intended for indoor use only.; Safety; certification; Certification column.
- Page 9 – CE Compliance; Compliance with EU Directives; Environmental Management; NI and the Environment; Waste Electrical and Electronic Equipment (WEEE); EU Customers; ⬉ᄤֵᙃѻક∵ᵻࠊᄣ⧚ࡲ⊩ ˄Ё; RoHS; Ёᅶ᠋; National Instruments; (For information about China RoHS compliance, go to
- Page 10 – Where to Go for Support; . If your product supports calibration, you can obtain the
USER GUIDE
NI Smart Camera I/O Accessory
This document describes the features of the NI Smart Camera I/O Accessory, what you need to get
started, installation and operation instructions, and accessory specifications.
The NI Smart Camera I/O Accessory features the following:
•
Spring terminals for two isolated inputs
•
Spring terminals for two isolated outputs
•
Spring terminals for the quadrature encoder inputs
•
Two power connection options
•
An RS-232 connector to communicate with the smart camera serial port
•
User-replaceable fuses for isolated outputs, RS-232, and accessory power
•
Built-in DIN rail clips for easy mounting
Figure 1 shows the accessory circuit board parts locator diagram.
Figure 1.
Front and Back Views of the NI Smart Camera I/O Accessory Circuit Board
1
Camera D-SUB Connector
2
RS-232 D-SUB Connector
3
24 VDC D-SUB Connector
4
Power In Selection Switch
5
24VDC Two-Position Connector
6
Isolated Output 1 Terminals
7
Isolated Output 0 Terminals
8
Quadrature Encoder Phase B Terminals
9
Quadrature Encoder Phase A Terminals
10 Isolated Input 1 Terminals
11 Isolated Input 0 Terminals
12 Spare Power Fuse
13 Power Fuse
14 Spare RS-232 Fuse
15 RS-232 Fuse
16 Isolated Output 0 Fuse
17 Spare Isolated Output Fuses
18 Isolated Output 1 Fuse
3
2
1
5
4
1
8
11
10
9
8
7
6
12
1
3
16
15
14
NATIONAL
INSTRUMENTS
NI SMART CAMERA
I/O ACCESSORY
17
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
NI Smart Camera I/O Accessory User Guide 2 ni.com What You Need to Get Started ❑ NI Smart Camera I/O Accessory kit, which includes the accessory, 15-pin D-SUB female to 15-pin D-SUB male cable, 2 m (part number 197817-02), and two-position header connector (Wago part number 734-102, available from w...
© National Instruments Corporation 3 NI Smart Camera I/O Accessory User Guide Operate the device only at or below Pollution Degree 2. Pollution is foreign matter in a solid, liquid, or gaseous state that can reduce dielectric strength or surface resistivity. The following is a description of polluti...
NI Smart Camera I/O Accessory User Guide 4 ni.com Installation To get started with the NI 17xx Smart Camera I/O Accessory, complete the following steps while referring to Figure 1. If you have not already installed the NI Smart Camera and required software, refer to Getting Started with the NI 17xx ...
