National Instruments NI USB-6009 - Manual
National Instruments NI USB-6009 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Feature
- Page 3 – Dimensions; Figure 3 illustrates the dimensions of the NI USB-6008/6009 device.; Safety Guidelines; Caution
- Page 5 – Related Documentation; DAQ Getting Started Guide; Start»All Programs»National Instruments»NI-DAQ»; Note
- Page 7 – DAQ; ANSI C without NI Application Software; NI-DAQmx C Reference Help; .NET Languages without NI Application Software
- Page 8 – Device Documentation and Specifications
- Page 9 – Training Courses; Installing the Software; Installing Other Software; for USB Devices Getting Started Guide; NI-DAQmx Base Getting Started Guide; Start»All Programs»National Instruments»
- Page 10 – and enter
- Page 13 – LED Indicator; LED State; Not lit
- Page 14 – Module
- Page 15 – GND
- Page 17 – Analog Input; MUX
- Page 19 – Connecting Reference Single-Ended Voltage Signals
- Page 20 – Digital Trigger; Analog Output
- Page 21 – DACs; Minimizing Glitches on the Output Signal; for more information about minimizing
- Page 22 – Digital I/O Circuitry; Source/Sink Information; for more information about how
- Page 23 – Place an ammeter in series with the load.
- Page 24 – Static DIO; Event Counter; Specifications
- Page 25 – Reference and Power Sources; software selectable
- Page 27 – mV maximum at full scale; Range
- Page 28 – External Voltage; to 5 V; Level
- Page 29 – Bus Interface; USB; Physical Characteristics
- Page 30 – MAINS; Safety Standards; Hazardous Locations
- Page 31 – Electromagnetic Compatibility; CE Compliance; Environmental Management; NI and the
- Page 32 – Waste Electrical and Electronic Equipment (WEEE); EU Customers; Where to Go for Support; you have access to everything from; ⬉ᄤֵᙃѻક∵ᵻࠊᄣ⧚ࡲ⊩ ˄Ё; RoHS
USER GUIDE AND SPECIFICATIONS
NI USB-6008/6009
This user guide describes how to use the National Instruments
USB-6008/6009 data acquisition (DAQ) devices and lists specifications.
Introduction
The NI USB-6008/6009 provides connection to eight analog input (AI)
channels, two analog output (AO) channels, 12 digital input/output (DIO)
channels, and a 32-bit counter with a Full-Speed USB interface.
Note
This manual revision updates naming conventions to reflect the conventions used in
NI-DAQmx. Table 1 notes the correlation between the old and updated names.
Table 1.
Digital Output Driver Type Naming Conventions
Hardware Functionality
NI-DAQmx Terminology
Open-drain
Open collector
Push-pull
Active drive
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
NI USB-6008/6009 User Guide and Specifications 2 ni.com Figure 1. NI USB-6008/6009 Top View Figure 2. NI USB-6008/6009 Back View Table 2. Differences Between the NI USB-6008 and NI USB-6009 Feature NI USB-6008 NI USB-6009 AI Resolution 12 bits differential, 11 bits single-ended 14 bits differential,...
© National Instruments Corporation 3 NI USB-6008/6009 User Guide and Specifications Dimensions Figure 3 illustrates the dimensions of the NI USB-6008/6009 device. Figure 3. NI USB-6008/6009 in Millimeters (Inches) Safety Guidelines Caution Operate the NI USB-6008/6009 only as described in these oper...
© National Instruments Corporation 5 NI USB-6008/6009 User Guide and Specifications • Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a st...
