National Instruments FP-PS-4 - Manuals

Page 2 - Use a flat-bladed screwdriver to unlock the DIN rail clip, as; Unlocking the Rail Clip; Attach the lip on the rear of the FP-PS-4 onto the top of a; Attaching the Module to a DIN Rail

FP-PS-4 Operating Instructions 2 ni.com 1. Use a flat-bladed screwdriver to unlock the DIN rail clip, as shown in Figure 1. Figure 1. Unlocking the Rail Clip 2. Attach the lip on the rear of the FP-PS-4 onto the top of a 35 mm DIN rail and press it down onto the DIN rail, as shownin Figure 2. Figure...

Page 3 - Positioning and Locking Your Module

© National Instruments Corp. 3 FP-PS-4 Operating Instructions 3. Slide the FP-PS-4 to the desired position along the DIN rail. For maximum cooling, leave a 25 mm (1.0 in.) space betweenthe FP-PS-4 and other devices on your DIN rail. After it is inposition, lock it to the DIN rail by pushing the rail...

Page 4 - Installing the Panel Mount Accessory; Lock the panel mount accessory into place by pushing the rail

FP-PS-4 Operating Instructions 4 ni.com Mounting Your FP-PS-4 on a Panel Follow these steps to install the optional FieldPoint network panelmount accessory and mount the FP-PS-4 power supply module toa panel. You can order the panel mount accessory, part number777609-01, from National Instruments. 1...

Page 5 - Caution

© National Instruments Corp. 5 FP-PS-4 Operating Instructions 4. Mount the FP-PS-4 to your panel with the panel mount accessory, as shown in Figure 5. The installation guide thatcomes with the panel mount accessory includes a template thatyou can use to drill pilot holes for mounting FieldPointmodul...

Page 6 - Cascading power from neighboring bases or; Wiring Power to Your FieldPoint Bank

FP-PS-4 Operating Instructions 6 ni.com needs. Select one or a combination of the methods to power thesignals of each of your I/O modules: • The signals of the I/O module are powered by an FP-PS-4 thatis connected to only that I/O module. • The signals of the I/O module share an FP-PS-4 with aneighb...

Page 7 - Note; Conductor Wire Color Standards for the Plug-in AC Input

© National Instruments Corp. 7 FP-PS-4 Operating Instructions Ensure that all the wiring is installed according to local codes andregulations by qualified electrical personnel. Follow these steps toconnect the FP-PS-4 to your FieldPoint system. 1. Use a 16 to 26 AWG stranded wire to connect the FP-P...

Page 8 - Connect the green or green/yellow conductor into the ground; When you install the conductors, make sure that; Specifications; Installation; Conductor Wire with the Correct Strip Length (drawing is to scale); Input Characteristics; AC fuse; Output Characteristics; Nominal continuous power

FP-PS-4 Operating Instructions 8 ni.com 6. Connect the green or green/yellow conductor into the ground terminal. Caution When you install the conductors, make sure that the entire conductor is in the screw terminal and that thereare no loose strands outside of the terminal. Only installone wire in e...

Page 9 - Physical; not; Electromagnetic Compatibility

© National Instruments Corp. 9 FP-PS-4 Operating Instructions Overload protection .......................... Protected against short circuits and output overload Physical Indicator ............................................ Green DC POWER LED Weight ............................................... ...

Page 10 - Declaration of Conformity; at; Mechanical Dimensions

FP-PS-4 Operating Instructions 10 ni.com regulatory compliance information. To obtain the DoCfor this product, click Declaration of Conformity at ni.com/hardref.nsf/ . Mechanical Dimensions Figure 9 shows the mechanical dimensions of the FP-PS-4.Dimensions are given in millimeters [inches]. Figure 9...

Page 11 - Where to Go for Support

© National Instruments Corp. 11 FP-PS-4 Operating Instructions Where to Go for Support For more information about setting up your FieldPoint system,refer to these National Instruments documents: • Your FieldPoint network module user manual • Your other FieldPoint I/O module operating instructions • ...