National Instruments FP-PS-4 - Manual
National Instruments FP-PS-4 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Use a flat-bladed screwdriver to unlock the DIN rail clip, as; Unlocking the Rail Clip; Attach the lip on the rear of the FP-PS-4 onto the top of a; Attaching the Module to a DIN Rail
- Page 3 – Positioning and Locking Your Module
- Page 4 – Installing the Panel Mount Accessory; Lock the panel mount accessory into place by pushing the rail
- Page 5 – Caution
- Page 6 – Cascading power from neighboring bases or; Wiring Power to Your FieldPoint Bank
- Page 7 – Note; Conductor Wire Color Standards for the Plug-in AC Input
- Page 8 – Connect the green or green/yellow conductor into the ground; When you install the conductors, make sure that; Specifications; Installation; Conductor Wire with the Correct Strip Length (drawing is to scale); Input Characteristics; AC fuse; Output Characteristics; Nominal continuous power
- Page 9 – Physical; not; Electromagnetic Compatibility
- Page 10 – Declaration of Conformity; at; Mechanical Dimensions
- Page 11 – Where to Go for Support
FieldPoint™, National Instruments™, NI™, and ni.com™ are trademarks of National Instruments Corporation.
Product and company names mentioned herein are trademarks or trade names of their respective companies.
323179A-01
©
2001 National Instruments Corp. All rights reserved.
November 2001
OPERATING INSTRUCTIONS
FP-PS-4
FieldPoint Power Supply
These operating instructions describe the installation, features, and
characteristics of the FP-PS-4.
Features
The FP-PS-4 is a FieldPoint power supply module with the
following features:
•
24 VDC output
•
Convenient DIN rail mounting or optional panel mounting
•
Universal AC power input: 90 to 264 VAC, 47 to 63 Hz
•
Modular FieldPoint form factor for easy integration with other
FieldPoint modules
•
15 W output for 0 to 50 °C operation
Installation
You can mount your FieldPoint system either to a DIN rail or
directly on a panel. The following sections give instructions for
both mounting methods.
Mounting Your FP-PS-4 on a DIN Rail
The FP-PS-4 power supply module has a simple rail clip for
reliable mounting onto a standard 35 mm DIN rail. Follow these
steps to mount the module on a DIN rail.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
FP-PS-4 Operating Instructions 2 ni.com 1. Use a flat-bladed screwdriver to unlock the DIN rail clip, as shown in Figure 1. Figure 1. Unlocking the Rail Clip 2. Attach the lip on the rear of the FP-PS-4 onto the top of a 35 mm DIN rail and press it down onto the DIN rail, as shownin Figure 2. Figure...
© National Instruments Corp. 3 FP-PS-4 Operating Instructions 3. Slide the FP-PS-4 to the desired position along the DIN rail. For maximum cooling, leave a 25 mm (1.0 in.) space betweenthe FP-PS-4 and other devices on your DIN rail. After it is inposition, lock it to the DIN rail by pushing the rail...
FP-PS-4 Operating Instructions 4 ni.com Mounting Your FP-PS-4 on a Panel Follow these steps to install the optional FieldPoint network panelmount accessory and mount the FP-PS-4 power supply module toa panel. You can order the panel mount accessory, part number777609-01, from National Instruments. 1...
