National Instruments cFP-20xx - Manuals

Page 2 - cFP-20xx Quick Start Guide; AU

106 mm (4.18 in.) Cabling Clearance Min. 182 mm (7.18 in.) 4 slots = 246 mm (9.68 in.)8 slots = 441 mm (17.4 in.) Cooling Outline 51 mm (2 in.) Cooling Outline 51 mm (2 in.) 127 mm (5.00 in.) Cabling Clearance Min. 165 mm (6.50 in.) Cooling Outline 51 mm (2 in.) All Around 4 slots = 246 mm (9.68 in....

Page 3 - Mounting the Backplane on a Panel; Do not use screws longer than

3 cFP-20xx Quick Start Guide © National Instruments Corporation Mounting the Backplane on a Panel A. Fasten the panel-mount plates to the back of the cFP-BP- x using a number 2 Phillips screwdriver and the 8-32 × 5/16 in. countersink screws shipped with the kit. B. Bolt or screw the panel-mount acce...

Page 4 - Mounting the Backplane on a DIN Rail; x using a

4 cFP-20xx Quick Start Guide ni.com Mounting the Backplane on a DIN Rail NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting or rackmounting for the cFP-BP-8. A. Fasten the DIN rail clip(s) to the cFP-BP- x using a number 2 Phillips screwdriver and the 8-32 × 5/16 in. countersi...

Page 5 - Mounting the Backplane in a Standard 19-in. Rack; x using the captive screws on

Mounting the Backplane in a Standard 19-in. Rack A. Fasten the rack-mount bracket to the back of the cFP-BP- x using the captive screws on the bracket. B. Bolt the rack-mount accessory to a standard 19-in. rack. C. Connect the PE ground terminal on the cFP-BP- x to safety ground. C CA AU UT TIIO ON ...

Page 6 - xx controller is right side up with the NI logo at the top, and

6 cFP-20xx Quick Start Guide ni.com IIn nsstta allll tth he e c cFFP P--2200 xxxx C Co on nttrro olllle err o on n tth he e B Ba ac ckkp plla an ne e A. Make sure that no power is connected to the controller or the backplane. B. Make sure that the cFP-20 xx controller is right side up with the NI lo...

Page 7 - tighten the captive screws to 1.1 N

7 cFP-20xx Quick Start Guide © National Instruments Corporation IIn nsstta allll II//O O M Mo od du ulle ess o on n tth he e B Ba ac ckkp plla an ne e A. Align the captive screws on the I/O module with the holes on the backplane. B. Press firmly to seat the I/O module on the backplane. C. Using a nu...

Page 8 - Use the connector socket to the right of each I/O module socket.

8 cFP-20xx Quick Start Guide ni.com IIn nsstta allll C Co on nn ne ec ctto orr B Bllo oc ckkss o on n tth he e B Ba ac ckkp plla an ne e In order to connect I/O modules to input signals or to external loads, you need to install a cFP-CB- x connector block or other connectivity accessory for each I/O...

Page 11 - D. Follow the onscreen instructions to complete the installation.

IIn nsstta allll S So offttw wa arre e o on n tth he e H Ho osstt P PC C A. Install the software packages you plan to use, such as LabVIEW, LabVIEW RT, Lookout, Measurement Studio, or LabWindows/CVI, before you install the FieldPoint software. The FieldPoint software installation installs the LabVIE...

Page 16 - and select

16 cFP-20xx Quick Start Guide ni.com C. To configure the hardware settings of a particular I/O module, right-click the device name and select E Ed diitt tth hiiss d de evviic ce e . The Device Configuration dialog box appears, as shown in the figure above. For output modules, you can choose settings...

Page 19 - xx controller in the left pane of FieldPoint Explorer, and select

19 cFP-20xx Quick Start Guide © National Instruments Corporation S Sa avviin ng g H Ha arrd dw wa arre e C Co on nffiig gu urra attiio on n a ass P Po ow we err--U Up p S Stta atte e When you are satisfied with the hardware configuration of the FieldPoint system, you cansave this configuration as th...

Page 20 - Network; Power Requirement; Power consumption

20 cFP-20xx Quick Start Guide ni.com S Sp pe ec ciiffiic ca attiio on nss Network Network interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10BaseT and 100BaseTX EthernetCompatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IEEE802.3Communication rates . ....

Page 21 - Physical Characteristics; must be lowered; Shock and Vibration; Operating vibration; 0 g, 11 ms half sine, 18 shocks at 6 orientations; Safety

21 cFP-20xx Quick Start Guide © National Instruments Corporation Physical Characteristics Screw-terminal wiring . . . . . . . . . . . . . . . . . . . . . . . . . . 16–26 AWG copper conductor wire with 7 mm (0.28 in.) of insulation stripped from the end Torque for screw terminals . . . . . . . . . . ...

Page 22 - Electromagnetic Compatibility; OT; Declarations of Conformity Information; at

22 cFP-20xx Quick Start Guide ni.com Electromagnetic Compatibility CE, C-Tick, and FCC Part 15 (Class A) CompliantEmissions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 55011 Class A at 10 m FCC Part 15A above 1 GHzImmunity . . . . . . . . . . . . . . . . . . . . . . . ....