National Instruments cFP-20xx - Manual
National Instruments cFP-20xx – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – cFP-20xx Quick Start Guide; AU
- Page 3 – Mounting the Backplane on a Panel; Do not use screws longer than
- Page 4 – Mounting the Backplane on a DIN Rail; x using a
- Page 5 – Mounting the Backplane in a Standard 19-in. Rack; x using the captive screws on
- Page 6 – xx controller is right side up with the NI logo at the top, and
- Page 7 – tighten the captive screws to 1.1 N
- Page 8 – Use the connector socket to the right of each I/O module socket.
- Page 11 – D. Follow the onscreen instructions to complete the installation.
- Page 16 – and select
- Page 19 – xx controller in the left pane of FieldPoint Explorer, and select
- Page 20 – Network; Power Requirement; Power consumption
- Page 21 – Physical Characteristics; must be lowered; Shock and Vibration; Operating vibration; 0 g, 11 ms half sine, 18 shocks at 6 orientations; Safety
- Page 22 – Electromagnetic Compatibility; OT; Declarations of Conformity Information; at
FieldPoint
TM
cFP-20
xx Quick Start Guide
What You Need
to Get Set Up
• cFP-20
xx LabVIEW RT controller
• Mounting hardware (DIN rail, panel-
mount, or rack-mount accessory)
• I/O module(s)
• cFP-BP-
x backplane, connector
blocks, cables
• 11–30 V power supply
• Accessories: Ethernet cable,
number 2 Phillips screwdriver
• PC running Windows
• FieldPoint software 3.0.2 or later
• LabVIEW RT
M
Mo
ou
un
ntt tth
he
e C
Co
om
mp
pa
ac
ctt FFiie
elld
dP
Po
oiin
ntt B
Ba
ac
ckkp
plla
an
ne
e
You can mount the cFP-BP-
x backplane on a 35 mm DIN rail, on a panel, or in a standard 19 in.
rack. Before using any of these mounting methods, record the serial number from the back of
the backplane.
Each set of mounting instructions in this document includes an instruction to connect the
protective earth (PE) ground terminal on the cFP-BP-
x backplane to the system safety ground.
The backplane PE ground terminal has the following symbol stamped beside it:
. Connect the
backplane PE ground terminal to the system safety ground using 14 AWG (1.6 mm) wire with a
ring lug. Use the 5/16 in. panhead screw shipped with the backplane to secure the ring lug to
the backplane PE ground terminal.
1
1
cFP-20xx Quick Start Guide
©
National Instruments Corporation
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
106 mm (4.18 in.) Cabling Clearance Min. 182 mm (7.18 in.) 4 slots = 246 mm (9.68 in.)8 slots = 441 mm (17.4 in.) Cooling Outline 51 mm (2 in.) Cooling Outline 51 mm (2 in.) 127 mm (5.00 in.) Cabling Clearance Min. 165 mm (6.50 in.) Cooling Outline 51 mm (2 in.) All Around 4 slots = 246 mm (9.68 in....
3 cFP-20xx Quick Start Guide © National Instruments Corporation Mounting the Backplane on a Panel A. Fasten the panel-mount plates to the back of the cFP-BP- x using a number 2 Phillips screwdriver and the 8-32 × 5/16 in. countersink screws shipped with the kit. B. Bolt or screw the panel-mount acce...
4 cFP-20xx Quick Start Guide ni.com Mounting the Backplane on a DIN Rail NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting or rackmounting for the cFP-BP-8. A. Fasten the DIN rail clip(s) to the cFP-BP- x using a number 2 Phillips screwdriver and the 8-32 × 5/16 in. countersi...
