Jet 578842 - Manuals

6 4.0 Specifications Table 1 Stock number 578842 577842 578634 577634 Model number IBDG-248 IBDG-248VS IBDG-436 IBDG-436VS Motor and Electricals Motor Type totally enclosed, induction, capacitor start totally enclosed, induction, with inverter totally enclosed, induction, capacitor start totally enc...

7 Dimensions Overall dimensions (L x W x H) Sanding arm vertical 23-7/16 x 15-1/16 x 25-29/32 in. (595 x 383 x 658 mm) 25-13/32 x 15-1/16 x 20-3/4 in. (645 x 383 x 527 mm) Sanding arm horizontal 23-7/16 x 26-27/32 x 12-7/32 in. (595 x 682 x 310 mm) 25-13/32 x 21-11/16 x 11-3/4 in. (645 x 551 x 298 m...

8 4.2 Machine dimensions/work area Primary dimensions in millimeters. (Parentheses show imperial dimensions.) Figure 4-2: dimensions for IBGB-248/-248VS Figure 4-3: dimensions for IBGB-436/-436VS

9 5.0 Carton contents Included accessories are shown on this page. The identifying letters are used in the assembly instructions. Hardware package Part no. IBGB248-HP or IBGB436-HP Qty. K Tool rest (for sanding belt) 1 L Flat washer 3/8 1 M Adjustable handle 3/8 x 5/8L 1 N Stand-off 1 O Socket hd ca...

10 6.0 Setup and assembly 6.1 Tools required for assembly Cross-point (Phillips) screwdriver 3mm hex wrench – provided 6mm hex wrench – provided Additional tools may be needed for securing sander to a stand or workbench. 6.2 Unpacking Separate all parts from the packing material. Check each part aga...

11 6.6 Sanding tool rest Loosen screw (A, Figure 6-3) with 6mm hex wrench and lower sanding arm to horizontal position. Install tool rest as shown in Figure 6-3, using a 6mm hex wrench. Note: The tool rest can remain installed when not in use. Simply adjust it outward to allow opening and closing of...

12 It is recommended that the sander be connected to a minimum 15-amp circuit with circuit breaker or fuse. If using fuses, they should be time-delay fuses marked “D”. Local codes take precedence over recommendations. 7.1 GROUNDING INSTRUCTIONS 1. All Grounded, Cord-connected Tools: This tool must b...

13 Table 2 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number (AWG), the heavier the cord. Amp Rating Volts Total length of cord in feet More Than Not More Than 120 240 25 50 50 100 100 200 150 300 A...

14 Contour sanding (horizontal position) – Contoured workpieces can be sanded over the drive wheel. Open the end cover and secure it by attaching its hook to the strap, as shown in Figure 9-1. Adjust tool rest and tighten in place. Figure 9-1 9.1.1 Disc sanding Place workpiece firmly against table a...

16 11.0 Optional accessories These accessory items, purchased separately, are available for your JET belt/disc sander. Contact your dealer to order, or call JET at the phone number on the cover. * The JDCS-505 may require a hose adaptor for your belt/disc sander; see our website for information. IBG...

17 12.0 Troubleshooting IBDG series Belt/Disc Sander 12.1 General mechanical and electrical problems Some corrections may require a qualified electrician. Symptom Possible Cause Correction Motor will not start. No incoming power. Verify that plug is properly inserted into receptacle. If so, check ma...

19 12.2 Digital readout error codes (Variable speed models) Message Possible Cause Correction * OCL Internal electronic overload has been tripped. Do not overload motor; reduce pressure of workpiece against wheels. OH IGBT protection activated. Inspect wire connections to U/V/W for possible short ci...

20 13.1.1 IBDG-248 Belt/Disc Sander – Exploded View

21 13.1.2 IBDG-248 Belt/Disc Sander – Parts List Index No Part No Description Size Qty 1 ................ IBGB248-01 .............. Motor Housing w/ Stator .......................................... ...................................... 1 2 ................ IBDG248-02 .............. Rotor ............

23 13.2.1 IBDG-248VS Belt/Disc Sander – Exploded View

24 13.2.2 IBDG-248VS Belt/Disc Sander – Parts List Index No Part No Description Size Qty 1 ................ IBGB248VS-01 .......... Motor Housing w/ Stator .......................................... ...................................... 1 2 ................ IBDG248VS-02 ......... Rotor ...............

26 13.3.1 IBDG-436 Belt/Disc Sander – Exploded View

27 13.3.2 IBDG-436 Belt/Disc Sander – Parts List Index No Part No Description Size Qty 1 ................ IBGB248-01 .............. Motor Housing w/ Stator .......................................... ...................................... 1 2 ................ IBDG436-02 .............. Rotor ............

29 13.4.1 IBDG-436VS Belt/Disc Sander – Exploded View

30 13.4.2 IBDG-436VS Belt/Disc Sander – Parts List Index No Part No Description Size Qty 1 ................ IBGB248VS-01 .......... Motor Housing w/ Stator .......................................... ...................................... 1 2 ................ IBDG436VS-02 ......... Rotor ...............

32 14.0 Electrical Connections 14.1 Wiring diagram for IBDG-248 and IBDG-436 14.2 Wiring diagram for IBDG-248VS and IBDG-436VS M G Green 115V/230V ACN ACL U V W Operation panel Input Power Red White Black

33 15.0 Warranty and service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time per...