Honeywell 1104 - Manuals

5 Copyright 2014 INNCOM by Honeywell Input/Output Connections Headers : The B578 contains the following headers:  H1: In Circuit Programming Header  J1: DC Jack 12VDC Input  M1: PoE Module header (02-9949)  H2: NU  H3: ES1 / ES2 header  H4: RS485 (203-251)  H5: RS485 (203-251) Note: RS485 con...

6 Copyright 2014 INNCOM by Honeywell PoE Powered B578 The B578 is an IEEE 802.3af compliant Powered Device (PD) interface with a current mode switching regulator, providing a complete power solution for PD applications. The B578 is an IEEE class 2 device. PoE devices are classified below: IEEE Class...

7 Copyright 2014 INNCOM by Honeywell gateway used for Ethernet to S5bus protocol conversion in a DIN rail housing configuration. SAP VC Configuration Material Name When entering the model number in SAP, use the following description: Name Description B578_Controller B57x Platform Root Part Number Th...

8 Copyright 2014 INNCOM by Honeywell OP/N Code Logic Board Type Part Number A0 DIN Rail Mounted Housings See “Individual Components” chapter B0 Surface Mounted Housings See “Individual Components” chapter

INNCOM DIRECT D-578 EDGE ROUTER INSTALLATION GUIDE 5 31-00720-01 INSTALLATION Important Safety Information and Installation Precautions Read the below instructions carefully for safety and installation. Local codes and practices Always install equipment in accordance with the National Electric Code ...

INNCOM DIRECT D-578 EDGE ROUTER INSTALLATION GUIDE 31-00720-01 6 IT / Network Requirements The D-578 routs data between the INNCOM “Room Gateway” device (D1-528 or D-X47) installed in each room and the Niagara service running on the INNCOM/Honeywell server PC (or Niagara JACE device in the future). ...

INNCOM DIRECT D-578 EDGE ROUTER INSTALLATION GUIDE 7 31-00720-01 D-578 Mounting Location • You must consider where the D-578 is mounted in relation to metal objects and the location of installed D1-528/D-X47 devices that will communicate through the D-578. If mounting the D-578 to a metal wall box, ...

INNCOM DIRECT D-578 EDGE ROUTER INSTALLATION GUIDE 31-00720-01 8 NOTE: NOTE: Do not connect the D-578 to a PoE switch port that is providing power and 12V DC to the D-578 J1 12VDC jack at the same time. GETTING STARTED D-578 Connectors, Leds and Buttons D-578 LED indications The D-578 comes with bot...

INNCOM DIRECT D-578 EDGE ROUTER INSTALLATION GUIDE 9 31-00720-01 a. On the D-578, press the blue Bind button 6 times (press-press-press-press-press-press). b. The D3 Red LED will start to rapidly blink indi - cating it is in key distribution mode. c. The D-578 will begin to broadcast its unique prop...

INNCOM DIRECT D-578 EDGE ROUTER INSTALLATION GUIDE 31-00720-01 10 and holding the F/C button on the D1-528 or D1-529 for 4 seconds. The display will show rid indicating service mode was entered. b. Go to the rUn service parameter and press DIS - PL AY. P and 0 will appear. c. Press the DOWN arrow bu...

INNCOM DIRECT D-578 EDGE ROUTER INSTALLATION GUIDE 11 31-00720-01 Factory Reset If required or directed to Factory Reset (Boot) the D- 578, perform the following steps: 1. Get access to the D-578 and remove the top enclo - sure cover. 2. Find the Blue Bind/Reset button located on the lower left corn...

INNCOM DIRECT D-578 EDGE ROUTER INSTALLATION GUIDE ® U.S. Registered Trademark ©2024 Honeywell International Inc. 31-00720-01 I Rev. 06-24 The material in this document is for information purposes only. The content and the product described are subject to change without notice. Honeywell makes no re...