Epson R1400- Manuals

Page 3 - Now the injector head can be moved from side to side by hand.

3 Check Printer Condition If you have a brand new printer, follow the Epson instructions for setting up your printer. Use the Epson cartridges that came with the printer. Follow normal installation instructions for the software. Test the printer by printing pictures. Learn how to use the Epson utili...

Page 4 - INSTALLATION OF YOUR ECO-FLO KIT; Step 1 Removing the Injector Lid; side disconnected, the second lug can; ONLY; along as; Scoring point

4 INSTALLATION OF YOUR ECO-FLO KIT Step 1 Removing the Injector Lid You will need to remove the printer lid on the injector carrier as shown illustrated from the diagrams below. Store this somewhere safe should you ever wish to return the printer to its original setup. The lid is held in place by tw...

Page 6 - Step 4 Tube Preparation; tubes stripped back

6 Step 4 Tube Preparation Using a pair of scissors snip gently at the end of each tube. Please see Fig.8 below. Strip back all the tubes by approx 150mm. Please note when assembling the tubes to the bottle caps you may need to strip back more of the tubing in order for the bottles to be seated corre...

Page 7 - Step 5 Preparation of The Clamps & Inks; LM

7 Step 5 Preparation of The Clamps & Inks You are now ready to attach the tube clamps to the tubes as indicated in Fig.11 below. Now please fill all the bottles with the correct inks; please ensure that all ink has been filled correctly as indicated by the bottle caps that are colour coded, see ...

Page 8 - Wing Adaptor

8 Step 7 Assembling the Tubing to the Bottle Caps When you have completed the above process insert the correct tubes to the correct ink bottles. PLEASE TAKE CARE when doing this as if this is connected incorrectly there is no turning back see Fig.13 & Fig.14 Step 8 Priming the Ink Through the In...

Page 11 - Arrow up

11 Step 10 Installing the Chip Support Bars When you have positioned the chip blocks into place you will need to insert and install the support bars as indicated the correct way up ( Arrow up ) as illustrated in Fig. 24. Please ensure that you insert the bars as illustrated in Fig.25 making sure tha...

Page 12 - . Push the injectors home; MUST; align the; Picture shows injectors fully installed in a

12 Step 11 Install Injectors Please place the set of 6 injectors in the printer carriage that is now parked in the centre of the printer. Carefully align them, and when you are happy the injectors are in position. PLEASE BE CAREFUL NOT TO PUSH TOO HARD, AS THIS WILL CAUSE DAMAGE TO THE INJECTOR &...

Page 13 - Align and locate the; SLOT; Slot within the printer head; Step 13 Unlocking the Tube Clamps; Please ensure that you; UNLOCK

13 Align and locate the SLOT in the R1400 printer head as indicated in Fig.32. W hen you have installed the special printer lid on the R1400 it should finish and look like Fig.33 with the tubes moulded in that position. Slot within the printer head Step 13 Unlocking the Tube Clamps Please ensure tha...

Page 14 - square from the right as illustrated.; The

14 Step 14 Installing the Central Tube Support Bracket & Aligning the Tubes The Tube Support Bracket has Self Adhesive Strips on it. Use an alcohol or cleaning solution and clean the top of the printer housing where the Tube Support Bracket is going to be attached, see Fig.36. Then make sure the...

Page 15 - DO NOT FULLY OPEN THE TUBE CLIP BACK AS THIS WILL SNAP!

15 Please ensure that the tubing has just enough slack which may need to be adjusted to allow movement of the print head without restriction. This can be done manually by moving the head to the left and right and checking that there is just enough tubing to allow the print head to move freely from l...

Page 18 - and continue printing in the normal way.

18 Step 17 Testing the System Push the injectors to the far right and plug the printer back on. Have your graphics program (e.g. Photoshop) open and ready to use. The printer should come on and the head should move back and forth a few times and do a cleaning cycle. When it stops moving, only the gr...

Page 19 - Please note before removing the injectors you; clamp the tubing on the relevant injectors by; LOCKING; the

19 Step 18 Removing the Injectors Please note before removing the injectors you MUST clamp the tubing on the relevant injectors by LOCKING the White tube clamps to avoid air traveling up the injector and into the tube. At this point press the ink change button on the front panel of the printer so th...

Page 21 - stay suspended in solution and gives constant results.; IMPORTANT; DO NOT; remove the injectors from the printer unless specifically; Removing; lift the inks above the Printer. This would cause the ink to flood

21 FAQ»S & Caring For Your Eco-Flo √ READ CAREFULLY!!! Here are some tips to make sure that your new system performs trouble-free. • It is advised to gently shake by rotation each ink bottle on a regular weekly basis. This is to ensure the XL (Xtra Life) Dye inks stay suspended in solution and g...