Epson R1400- Manual
Epson R1400– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Now the injector head can be moved from side to side by hand.
- Page 4 – INSTALLATION OF YOUR ECO-FLO KIT; Step 1 Removing the Injector Lid; side disconnected, the second lug can; ONLY; along as; Scoring point
- Page 6 – Step 4 Tube Preparation; tubes stripped back
- Page 7 – Step 5 Preparation of The Clamps & Inks; LM
- Page 8 – Wing Adaptor
- Page 11 – Arrow up
- Page 12 – . Push the injectors home; MUST; align the; Picture shows injectors fully installed in a
- Page 13 – Align and locate the; SLOT; Slot within the printer head; Step 13 Unlocking the Tube Clamps; Please ensure that you; UNLOCK
- Page 14 – square from the right as illustrated.; The
- Page 15 – DO NOT FULLY OPEN THE TUBE CLIP BACK AS THIS WILL SNAP!
- Page 18 – and continue printing in the normal way.
- Page 19 – Please note before removing the injectors you; clamp the tubing on the relevant injectors by; LOCKING; the
- Page 21 – stay suspended in solution and gives constant results.; IMPORTANT; DO NOT; remove the injectors from the printer unless specifically; Removing; lift the inks above the Printer. This would cause the ink to flood
1
IMPORTANT
If your printer is new, set it up according to
the enclosed manufacturers instructions.
This is a check to ensure your new printer
and drivers are working correctly before the
Eco-Flo System is installed.
ECO-FLO CONTINUOUS INK SYSTEM
Perma
Jet
Assembly Instructions for
:
R1400
Ink System
I
t is very important you read these instructions carefully before you begin!
We will take you through the following steps:
1
Preparing your Injector
2
Setting up of the Inks in the bottle tray
3
Installation of the modified injector to your printer
4
Fitting of the Tube Supports System
5
Producing your first print.
Only start work on the installation once you have read the
instructions fully!
What you will need to Install the Eco-Flo R1400
*
Complete Eco-Flo R1400 Kit
*
Sharp Blade (Stanley Knife type) & Scissors
*
Measuring Tape or Ruler
*
Marking Pen or Pencil
*
Paper Towels
Please read carefully before you continue
and
refer to the components diagram over the
page
What is included in your Eco-Flo R1400 Kit
*
Injector Set with tubes attached
*
Set 6 Inks & empty 100ml bottles
*
6 Bottle Caps & clear piping tubes
*
Tube Support Bracket with Self Adhesive
Pads fitted
*
Bottle Holder Tray
*
Special Injector Lid & 2 Chip Blocks
*
1x Grey/W hite Tube Clip with adhesive pad
*
Installation Instructions and Profiles CD
*
10ml Syringe & wing adaptor
*
Pair of latex gloves
*
6 Tube Clamps
*
Foam Strip
Epson R1400 Eco-Flo Shown
Epson R1400
Part No. APJ29421
EPSON PRINTER
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Epson R1400
Summary
3 Check Printer Condition If you have a brand new printer, follow the Epson instructions for setting up your printer. Use the Epson cartridges that came with the printer. Follow normal installation instructions for the software. Test the printer by printing pictures. Learn how to use the Epson utili...
4 INSTALLATION OF YOUR ECO-FLO KIT Step 1 Removing the Injector Lid You will need to remove the printer lid on the injector carrier as shown illustrated from the diagrams below. Store this somewhere safe should you ever wish to return the printer to its original setup. The lid is held in place by tw...
6 Step 4 Tube Preparation Using a pair of scissors snip gently at the end of each tube. Please see Fig.8 below. Strip back all the tubes by approx 150mm. Please note when assembling the tubes to the bottle caps you may need to strip back more of the tubing in order for the bottles to be seated corre...
