Epson P07303- Manuals

2 2 3. Unpacking and Checking the Parts G 501 m m 191 m m 225 mm 93 mm 281 m m Pole Display Module Flat Cable (DB-9P to DB-9P flat cable connector) Base Unit Two pieces of pole support (1x22cm, 1x9cm) Installation guide Power Adapter 4. Interface 4.1. Specifications Data transmission: Serial Synchro...

3 3 4.2. Interface 4.2.1. Stand alone VFD Pole Display base Below illustrate the configuration of Stand alone VFD Pole Display base. Figure of VFD Pole Display Base 4.2.2. Interface connector PWR COM RJ45 PWR: Power input connector from adapter „ Connector type: DC jack (5.5/2.1) „ Pin assignment: N...

4 4 5. Dip Switch and Software Setting 5.1. Command type selection SW1 SW2 SW3 Command type Demo mode support Default ON ON ON POS7300 No ＊ OFF ON ON EPSON ESC/POS Yes ON OFF ON ADM 787/ ADM 788 No OFF OFF ON DSP800 Yes ON ON OFF AEDEX/ EMAX No OFF ON OFF UTC/P No ON OFF OFF UTC/S No OFF OFF OFF CD5...

6 6 5.7.4. Command type setting command STX 05 C n ETX /Change the command type setting/ ASCII Format STX 05 C n ETX Dec. Format [02][05][67] n [03] Hex. Format [02h][05h][43h] n [03h] 30h ≦ n ≦ 37h Description This command will change the command type and initialize the display. The display emulati...

7 7 6. Command List Table Command List Table – 1 EPSON POS7300 CD5220 D101 UTC/S UTC/P AEDEX ADM788 DSP800 Move cursor right O O O Move cursor left O O O Move cursor up O O O Move cursor down O O O Move cursor to right-most position O O O Move cursor to left-most position O O O Move cursor to home p...

8 8 Command List Table – 2 EPSON POS7300 CD5220 D101 UTC/S UTC/P AEDEX ADM788 DSP800 Upper line message scroll once pass O O Change attention code O O Two line display O O Clear upper line and move cursor to upper left-end position O Clear bottom line and move cursor to bottom left-end position O Se...

11 11 Note: 3. The parameter of international fonts set control by command “ ESC f n ” Parameter “n” International Font Set ‘A’ U.S.A. ‘G’ Germany ’I’ Italy ‘J’ Japan ‘U’ U.K. ‘F’ France ‘S’ Spain ‘N’ Norway ‘W’ Sweden ‘D’ Denmark I ‘E’ Denmark II ‘L’ Slavonic ‘R’ Russia 4. The parameter of the code...

13 13 7.8. EPSON ESC/POS command list Command Code (hex) Function description ESC t n 1B 74 n (n=00-0fh) Select character code table. See Table 7-2. ESC R n 1B 52 n (n=00-0fh) Select international character set. See Table 7-1. US r n 1F 72 n (n=00,01) Select/cancel reverse character. US MD1 1F 01 Sp...

17 17 8.8. Page 5 (PC865: Nordic) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H Ç ü é â ä à å ç ê ë è ï î ì Ä Å 90H É æ Æ ô ö ò û ù ÿ Ö Ü ø £ Ø Pt ƒ A0H á í ó ú ñ Ñ a o ¿ ⌐ ¬ ½ ¼ ¡ « ¤ B0H ░ ▒ ▓ │ ┤ ╡ ╢ ╖ ╕ ╣ ║ ╗ ╝ ╜ ╛ ┐ C0H └ ┴ ┬ ├ ─ ┼ ╞ ╟ ╚ ╔ ╩ ╦ ╠ ═ ╬ ╧ D0H ╨ ╤ ╥ ╙ ╘ ╒ ╓ ╫ ╪ ┘ └...

19 19 9. Command details 9.1. Overwrite mode In this mode, the cursor will move rightward and begin from the upper left-end position. When the cursor reached the end of the upper line, the cursor will move down to the bottom left-end position to continue. When the cursor reached the end of the botto...

21 21 10. Control code set HEX CODE HEX CODE 00H NULL 10H DLE 01H SOH, MD1 11H DC1 02H STX, MD2 12H DC2 03H ETX, MD3 13H DC3 04H EOT, MD4 14H DC4 05H ENQ, MD5 15H NAK 06H ACK, MD6 16H SYN 07H BEL, MD7 17H ETB 08H BS, MD8 18H CAN 09H HT 19H EM 0AH LF 1AH SUB 0BH VT, HOM 1BH ESC 0CH FF, CLR 1CH FS 0DH...

22 22 Appendix A: Display Module Dimension 70mm 39mm 0.38o 200mm 176mm 158.6mm 9.0mm 0.25mm 5.25mm 0.85mm 0.25mm 1.5mm 1.05mm 1.5mm 1.5mm 22.5mm 9.5mm 6.65mm

1 1. Features (1) Data can be display on 20 columns x 2 lines. (2) Blue–green color and large character are easy to see (3)The DIP switches setting emulate commands mode, baud rate and international character. (4) Command emulation modes include POS7300/ CD5220 II/ ADM787/ UTC / AEDEX/ Epson/ DSP800...

2 2. General Specification NO ITEM Descriptions 1 Display method Vacuum fluorescent display 2 Number of character 40 characters ( 20 columns x 2 lines) 3 Character font 5 x 7 Dot matrix 4 Display color Blue green 5 Brightness 700 cd / 6 Character type 96 alphanumeric 13 kinds of international charac...

3 3 Unpacking and Checking the Parts • Pole Display Module • Flat Cable (DB-9P to DB-9P flat cable connector ) • Base Unit • Two pieces of pole support (1x22cm, 1x9cm) • Installation guide • Power Adapter G 501 m m 191 m m 225 mm 93 mm 281 m m

4 4. Interface 4.1 Specifications Data transmission: Serial Synchronization: Asynchronous Handshaking: DTR / DSR Signal level: MARK = -3 to –15 V (logic “1”) SPACE = +3 to +15 V (logic “0”) Baud rates: 4800,9600,19200,38400 bps Parity: None, even Bit length: 8 bits Stop bits: 1 or more 4.2 The commu...

6 10 1 9 6 6 1 5 1 10 1 CN2: RS-232C connects to PC/Host CN3: Connect to display panel CN6: Power supply connector CN1,CN4, CN5: No used Power Supply Connectors CN6 / Connector type: DC jack (5.5/2.1) Pin assignment No Signal + Vin - GND RS232C link to PC/HOST connector CN2 / Connector type: D-sub 9...

7 5. Dip Switch and Software Setting 5.1 Command type selection SW1 SW2 SW3 Command type Default ON ON ON POS7300 OFF ON ON ESC/POS ON OFF ON ADM 787 OFF OFF ON DSP800 ON ON OFF AEDEX OFF ON OFF UTC/P ON OFF OFF UTC/S OFF OFF OFF CD5220 5.2 Baud rate selection SW8 SW9 Baud rate (bps) Default ON ON 4...

8 5.5 International character set SW4 SW5 SW6 SW7 Character set Code table ( 80H-FFH) ON ON ON ON *default U.S.A. PC-437(USA, standard Europe) OFF ON ON ON FRANCE PC-850(multilingual) ON OFF ON ON GERMANY PC-850(multilingual) OFF OFF ON ON U.K. PC-850(multilingual) ON ON OFF ON DENMARK I PC-850(mult...

9 5.7. Software Status Setting When system POWER ON, there is no need to turn off to modify Command Type, Baud Rate, Parity, Demo Mode and International Character. To re-set DIP Switch to various Command Type under the following list of Command to modify the setting. The setup value will stored in t...

10 0 N nternational font n nternational font 30h .S.A. 38h APAN 31h RANCE 39h ORWAY 32h GERMANY 3Ah DENMARK II 33h .K. 3Bh LAVONIC 34h DENMARK I 3Ch RUSSIA 35h WEDEN 3Dh .S.A. 36h TALY 3Eh ot used 37h PAIN 3Fh ser define pattern 5.7.3 Command type select STX 05 C n ETX /Change command type/ ASCII Fo...

11 1 5.7.4 Reset EEPROM STX 05 07 n ETX /Reset EEPROM/ ASCII Format STX 05 07 n ETX Dec. Format [02][05][07][n][03] Hex. Format [02h][05h][07h][n][03h] Description This command will reset the content of EEPROM (e.g. Demo scroll data, user-define character) N Description 31h Clear all EEPROM contents...

12 2 5.7.7 Set Communication parity STX 05 P n ETX /Parity check selection/ ASCII Format STX 05 P n ETX Dec. Format [02][05][80] n [03] Hex. Format [02h][05h][50h] n [03h] n=30h,31h Description Change the display communication parity. Set 8 data bit and the parity set for even or non-parity. N Parit...

13 3 6. Command List Table Table –1 FLYTECH PARTNER EPSON GIGA POS7300 CD5220 D101 UTC/S UTC/P AEDEX ADM788 DSP800 Move cursor right O O O Move cursor left O O O Move cursor up O O O Move cursor down O O O Move cursor to right-most position O O O Move cursor to left-most position O O O Move cursor t...

15 5 7. Command 7.1. POS7300 series command set POS7300 Standard Mode Command List Command Code (hex) Function Description ESC F A .. CR 1B 46 41 [DATA X 40] 0D Write string to upper line ESC F B .. CR 1B 46 42 [DATA X 40] 0D Write string to lower line ESC F D .. CR 1B 46 44 [DATA X 40] 0D Upper lin...

18 8 *2: The parameter of international fonts set control by command “ESC f n” Parameter n International Font Set ‘A’ U.S.A. ‘G’ Germany ’I’ Italy ‘J’ Japan ‘U’ U.K. ‘F’ France ‘S’ Spain ‘N’ Norway ‘W’ Sweden ‘D’ Denmark I ‘E’ Denmark II ‘L’ Slavonic ‘R’ Russia *3: The parameter of the code table co...

23 3 8. Character Set 8.1 International Character Sets 8.2 USA, Standard Character Sets (20H – 7EH)

31 1 9.26 Character font format One font consists of 5 bytes’ string. The string format is: it yte 1 R7C1 R6C1 R5C1 R4C1 R3C1 R2C1 R1C1 yte 2 R7C2 R6C2 R5C2 R4C2 R3C2 R2C2 R1C2 yte 3 R7C3 R6C3 R5C3 R4C3 R3C3 R2C3 R1C3 yte 4 R7C4 R6C4 R5C4 R4C4 R3C4 R2C4 R1C4 yte 5 R7C5 R6C5 R5C5 R4C5 R3C5 R2C5 R1C5 ...

32 2 Appendix A: Display Module Dimension 70mm 39mm 0.38o 200mm 176mm 158.6mm 9.0mm 0.25mm 5.25mm 0.85mm 0.25mm 1.5mm 1.05mm 1.5mm 1.5mm 22.5mm 9.5mm 6.65mm