Epson ELPMB27- Manuals

Page 2 - Safety Instructions; Explanation of Symbols; Warning

2 Safety Instructions Before using the wall mount, make sure you read all of the safety instructions below and then save this manual for later reference. Incomplete or incorrect installation could cause damage to the product or result in personal injury or property damage. For additional information...

Page 3 - English; Caution

3 English In order to resist vibration and support the weight of the projector and optional accessories, use M8 nuts and bolts and tighten all screws firmly after installation. Otherwise, the projector or wall mount may fall and cause personal injury or property damage. Epson accepts no responsibili...

Page 4 - Before Use; Choosing a Location

4 Before Use This product is used for mounting the following short throw projectors to a wall: EB-435W/EB-430/EB-425W/EB-420/PowerLite 435W/PowerLite 430/PowerLite 425W/PowerLite 420. Choosing a Location Determine where you will install the wall mount and prepare the location in advance. Also, make ...

Page 5 - Package Contents

5 English Package Contents Use only the supplied bolts to install the wall mount. Do not substitute these bolts with any other types. You need to use commercially available M8 x 50 mm anchors (at least 3) to attach the wall plate to the wall. Gather the tools and parts you need before you begin inst...

Page 6 - Specifications

6 Specifications Weight Approx. 10 kg (22 lbs.) Maximum load capacity 5.5 kg (12.13 lbs.) Arm length 1510 mm (15.45 inches) (from wall plate attachment point to arm cover point) Vertical slide adjustment range 0 to 134 mm (0 to 5.27 inches) (arm length minimum)0 to 230 mm (0 to 9.05 inches) (arm len...

Page 7 - Screen Size and Projection Distance

7 English Screen Size and Projection Distance Refer to the tables on the following pages and install the mount and projector to project images at the appropriate size. The values are only a guide.The recommended projection distance is 70 to 119 cm (27.55 to 46.85 inches). Center of lens Projected im...

Page 12 - Assembly and Installation; Installing the wall plate

12 Assembly and Installation Make sure you follow the instructions below to install the wall mount. Otherwise, the wall mount may fall and result in personal injury or property damage. 1. Installing the wall plate 1) Check the position where you want to install the wall plate, and then mark that pos...

Page 14 - Assembling the wall mount

14 2. Assembling the wall mount 1) Attach the adjustment unit to the arm unit. 2) Secure temporarily using the hexagonal wrenches (M4 and M8) and M4 x 12 mm hexagon socket head cap bolt and M8 x 15 mm hexagon socket head cap bolt. 3) Attach the arm plate using a hexagonal wrench (M8) and four M8 x 1...

Page 15 - Routing the cables through the arm unit

15 English 3. Routing the cables through the arm unit If you are installing ELPIU03 (sold separately), you also need to route the USB cable supplied with ELPIU03 through the arm unit. 4. Attaching the wall mount to the wall plate 1) Attach the hook on the arm plate to the bar on the wall plate.Be ca...

Page 16 - Attaching the attachment plate to the projector; Attaching the projector to the adjustment unit

16 5. Attaching the attachment plate to the projector 1) Place the projector upside down. 2) Attach the attachment plate to the projector using the hexagonal wrench (M4) and five M4 x 12 mm bolts with washers/spring washers. 6. Attaching the projector to the adjustment unit 1) Slide the attachment p...

Page 17 - Connecting the cables; Attaching the arm cover

17 English 7. Extending the arm, adjusting the length, and securing temporarily 1) Loosen the screw on the arm.( ) 2) Adjust the length of the arm using the measure on the bottom to match the projection distance recommended in "Screen Size and Projection Distance" on page 7.( ) 3) After adju...

Page 18 - Turning on the projector and checking the screen

18 10. Turning on the projector and checking the screen 1) Plug in the projector. 2) Turn on the projector. 3) Loosen the screws on the adjustment unit (A, B, C, and D) as shown below to adjust the screen position. 4) Adjust the vertical slide (arm angle) using screw (E) on the bottom of the arm pla...

Page 19 - Attaching the interface cover bracket

19 English 11. Attaching the interface cover bracket Attach the interface cover bracket using the hexagonal wrench (M4) and two M4 x 12 mm bolts with washers. 12. Attaching the cable cover Take up the cable slack, and then secure the cable cover with the screws as shown below. Interfacecover bracket...

Page 20 - Attaching the wall plate cover

20 13. Attaching the wall plate cover Secure the wall plate cover with a hexagonal wrench (M4) and three M4 x 12 mm hexagon socket head cap bolts. Installation, removal, and servicing of the projector should only be performed by a qualified technician. See the User’s Guide included with your project...