Canon 400D - Manuals - manualsarea.com

Page 2 - . Specifications 400D

2 . Specifications 400D Test Pressure 10 Bar (300 ft.) Housings are individually tested Closure Design Air Lock Body Material Polycarbonate Overall Size 200 x 300 x 230 mm (LxWxH) Total Weight Approximately 2.6 Kg (Housing only) Buoyancy (with camera) Approximately neutral in salt water Features • V...

Page 3 - . Function Controls 400D

3 . Function Controls 400D 1. Pressure release plug 2. Display on/off 3. Menu 4. Jump 5. Playback 6. Erase 7. Viewfinder eyepiece 8. A/E Compensation 9. Drive Mode 10. AE/FE Lock 11. AF Point Selection 12. 13. 14. 15. Cross Key 16. Setting 17. Shutter 18. Main Dial 19. Mode Dail / Power on/off 20. F...

Page 4 - pulled out all the way

4 . Set up Instructions 4.1 Air Lock: The body and lid are designed with the Air Lock System “no clip” closure arrangement. Testing has shown that this arrangement allow the water to exert an even pressure on the O-ring, Increase the reliability of the watertight seal. 4.2 Pressure release plug To o...

Page 5 - Special note on responsibility for watertight integrity:; the working depth or dive down to the safe diving range.; guidance in using and maintaining the O-ring seal.

(Fig. 2) D80 Opening Key / Lever (Fig. 3) Turn to open 4.4 Special note on responsibility for watertight integrity: Each housing is individually inspected and hydrostatically tested in the factory. The design of the main piston O-ring seal is among the most reliable in the industry and the watertigh...

Page 6 - Place the lid on a firm non-slip level surface.; IF THE O-RING IS DAMAGED OR SUSPECTED OF BEING DAMAGED, DISCARD IT; Once the O-ring has been inspected and verified fit for use, apply a; SMALL; amount of Silicone grease to; Mounting the camera in the housing:

thoroughly toweled dry before opening up. After removing the lid and servicing the camera, replace the lid straight away, rather than leaving it lying around. Before replacing the lid, make sure that no contamination such as dust, hair, salt, sand etc. has fallen onto the O-ring or O-ring recess, as...

Page 7 - Screw home

(Fig. 7) (Fig. 8) (Fig. 9) Replace the lid (Fig. 8). Remember to ensure the pressure release plug is pulled all the way out while closing, otherwise the air cannot escape. Squeeze the lid closed all the way with the hissing of expelled air. Screw home (CLOCKWISE) the pressure release plug (Fig. 9). ...

Page 8 - Before diving, make sure the pressure release plug is pushed

After replacing the lid, make a final visual inspection of the main O-ring for contamination (Fig. 10). (Fig. 10) Note: If the O-ring is in good contact, a thin black line, about 0.5 to 1mm in width should be visible, where the O-ring is in contact with the lid. Follow this line all the way round th...

Page 9 - Pre Dive Function Check.; Check housing is closed.; or a cleansing tank where the water may be heated up by the sun.; and shutter extension, and wrap the camera in foam or bubble wrap.

5 . Use & Care of Housing: 5.1 Pre Dive Function Check. Just before entering the water, make a habit of reviewing that you have carried out the proper steps to close the housing. and the pressure release plug screwed home. Make a visual check of the O-ring seal. It is also useful to switch on th...

Page 10 - Hydrostatic pressure test to 10 Bar.

5.5 Accidents. The impact resistance of the housing is excellent. However after an accident the alignment of the housing may have been damaged. Therefore in the event of your housing suffering an impact force, e.g. being dropped, it is essential you do not use the housing for diving. Please return t...

Page 11 - applies only to the housing itself.; 0 BAR does not accept any liability either; Underwater Housing at the address below, to validate the warranty.; Please keep this document for future reference

7 . Warranty The warranty is valid within two years from the date of first purchase. The warranty applies only to the housing itself. 10 BAR does not accept any liability either implicit or otherwise for any equipment housed inside, or used together with the housing. In the event of the housing floo...