Canon 150DIGITAL - Manuals

Canon 150DIGITAL – Manual in PDF format online.

Manuals:

Manual

Manual Canon 150DIGITAL

Summary

Page 3 - WARNINGS; delivered with the flash.

1 WARNINGS • Never try to open the unit - the internal high voltage is potentially lethal. The unit may be serviced only by authorised service centres. • Shooting a flash close to eyes can seriously injure them. • Use only the original charging unit and TTL cable which are delivered with the flash. ...

Page 4 - compartment; FRONT

2 CONTROLS AND PARTS CONTROL PANEL 1 - Power switch and mode selector 2 - TTL / MAN selector 3 - Ambient light meter for display 4 - LED display 5 - Ready light indicator 6 - Battery compartment 7 - Synchro cable socket FRONT 8 - Macro protection ring – removable for wide angle 9 - Slave sensor 10 -...

Page 5 - BATTERY PACK

BATTERY PACK 12 - Power adapter socket 13 - Recharger LED indicator 14 - Data pin 15 - minus (-) Battery pin 16 - plus (+) Battery pin

Page 6 - COMPATIBLE CAMERAS; is suitable for CANON and NIKON; DIGITAL; is compatible with the following; DIGITAL; is compatible with the following

3 COMPATIBLE CAMERAS The SEAFLASH 150 DIGITAL is suitable for CANON and NIKON cameras. It is compatible with digital / film cameras in E-TTL, I-TTL, film -TTL and in manual mode. CANON The SEAFLASH 150 DIGITAL is compatible with the following CANON digital / film cameras listed in E-TTL, film-TTL an...

Page 7 - GENERAL DESCRIPTION; Feature

4 GENERAL DESCRIPTION The SEAFLASH 150 DIGITAL is fully controlled by a micro processor. Some of the significant advantages of using a micro controller are the possibility of managing digital communication on a serial bus with a digital camera and the possibility of easily updating the firmware in o...

Page 12 - IMPORTANT – FOR NIKON USERS; slave; SEACAM; Attention

IMPORTANT – FOR NIKON USERS For I-TTL use with NIKON cameras S6 sockets on the flash and the camera are recommended. Connect the main flash (master) always to the left socket – the 2.flash ( slave ) to the right socket. If two strobes are used you have to use the dedicated SEACAM - NIKON digital dua...

Page 14 - in the; The temperature inside the flash is above 65°C. This

with a true S.O.S. function. With the power switch (1) in the SOS position a true S.O.S. light signal is generated. This feature can also be used to test the flash. Attention Use the S.O.S. signal only when really needed and never use it to discharge the battery. 9 DISPLAY ERROR CODES If an error is...

Page 16 - manual; 2 CONNECTIONS

• User manual 12 CONNECTIONS Connect the flash to the housing and the camera only as described below. Battery power supply plug Input: 12-14V, 1.5A DC CANON Syncro socket S6 (wires rear view) 1 – Trigger 2 – Camera Data 3 – Ground 4 – TTL / Clock 5 – Ready / Clock 6 – Flash Data CANON digital 1/2 fl...

Page 17 - Never connect two flash devices parallel to a digital; Syncro socket N5

NIKON Attention Never connect two flash devices parallel to a digital NIKON camera. It can result in serious damage of flash and camera. Syncro socket N5 (wires rear view) 1 – Trigger 2 – TTL / Data 3 – Ground 4 – Acknowledge 5 – Ready / Clock Syncro socket S6 (wires rear view) 1 – Trigger 2 – TTL /...

Page 18 - Nikon film 2 flash; digital

Nikon film 2 flash NIKON digital 2 flash no digital dual strobe connector (S-N DDSC) installed. NIKON digital 2 flash S-N DDSC SEACAM - NIKON digital 1 2 3 4 5 Camera Mounting-f oot top view 1 2 3 4 5 1 2 3 4 5 D 2 BA T 46 D 1 BA T 46 D 1r BA T 46 D 2r BA T 46 D 1x BA T 46 D 2x BA T 46 1 2 3 4 5 Cam...

Page 19 - FLASHARM FIXATION

dual strobe connector installed. (connection on component side) Connect all wires to the housing socket and to the camera hot shoe following the numbering J1 main strobe (master) J2 2. Strobe (slave) J3 camera (hot shoe) FLASHARM FIXATION Use the M8 stainless steel insert thread at the bottom of the...

Page 20 - 3 TECHNICAL DETAILS AND FEATURES; , temperature and time, charging time 100

13 TECHNICAL DETAILS AND FEATURES • CANON digital E-TTL / film-TTL • NIKON digital I-TTL/ film-TTL • Energy 150 Ws • Uw-guide number 14 - ISO 100 / 1m at full power • Coverage light angle 130° • 180 flashes at full power • Recycle time 0,1 – 2 sec. • Manual light level selection in 7 + 5 different s...

Page 21 - 4 WARRANTY

14 WARRANTY A 24 month warranty from the date of invoice for function and tightness applies to the flash delivered. This warranty is valid within the EU member countries – for non EU member countries the warranty of the country to where the article is delivered applies. Warranty repairs do not exten...