Avaya X330W-2DS1 - Manuals - manualsarea.com

Page 2 - Important Safety Information

Important Safety Information Before installing or removing any components of a device, or carrying out any maintenancework, you must read the safety information provided. CAUTION: To avoid damage from static, only hold the WAN Expansion Router Module by the edges. Do not touch the top or bottom of t...

Page 3 - Unpack the Module; Equipment

Unpack the Module Check the package contents for the following: Equipment • One X330WAN Access Router Module. L Connection cables are not supplied. Documentation • Avaya X330WAN Access Router Modules Quick Start Guide (this document). • Avaya X330WAN Access Router Modules Release Notes. • Avaya X330...

Page 4 - Insert the Module

Insert the Module To insert an X330WAN into an Avaya P330 switch:1. Remove the blanking plate or other expansion module (if installed). 2. Insert the WAN expansion module gently into the slot, ensuring that the Printed CircuitBoard (PCB) is aligned with the guide rails. L The PCB fits into the guide...

Page 5 - Connect the Ports; Connecting the E1/T1 Ports; Connecting the Console Port

4 Connect the Ports Connecting the E1/T1 Ports To connect a T1/E1 module to a network, use a straight-through RJ-48C-to-RJ-48C cable toconnect the E1/T1 port to an RJ-48C wall jack. Connecting the Ethernet Port A UTP Category 5 cable must be connected to the 100Base-TX port, via an RJ45 connector. T...

Page 6 - Configure the Module; Establishing a Serial Connection; Establishing a Modem Connection; Enter

5 Configure the Module L Before you can set up the X330WAN module you must power on and set up the AvayaP330 stack as described in the Avaya P330 User ’s Guide. L Before using the X330WAN module you must assign an IP address via the CommandLine Interface (CLI) or via a Telnet session to the switch w...

Page 8 - exit

Configuring Loopback Interfaces L All CLI commands mentioned in this section are described in the Avaya P330 Reference Guide. To configure Loopback interfaces:1. Use the interface loopback <loopback number> command to enter the Interface Loopback mode. For example, typing interface loopback 1 ...

Page 9 - Configuring E1/T1 Interfaces

Configuring E1/T1 Interfaces L All CLI commands mentioned in this section are described in the Avaya P330 Reference Guide. To configure E1/T1 interfaces:1. Use the show controllers command to check if your controller ’s mode is configured as E1 or T1. Use the ds1-mode <e1 | t1> command to chan...

Page 10 - Establishing a Telnet Connection; Start

Changing the Primary Management Interface (pmi). L The default pmi is the first interface you define. To change the pmi:1. Enter one of the interface contexts as explained before. 2. If there no ip assigned on that interface use the | ip address <ip_ addr>< net- mask> command. 3. Use the...

Page 11 - X330WAN Default Settings; Function

X330WAN Default Settings The default settings for the X330WAN and its ports are determined by its embedded software.These default settings are subject to change. Newer versions of the software for the X330WANcan be downloaded from the Avaya Network Software Download Web site(http://www.avayanetwork....

Page 12 - root

Run the Web-Based Manager (optional) L To configure the Avaya X330WAN you can use the P330 Web-based Manager in addition to using the CLI. System Requirements Minimum hardware and Operating System requirements are:• Pentium® II 400 Mhz-based computer with 128 Mb of RAM• Screen resolution of 1024 x 7...

Page 13 - Either; Or

L If the network manager has configured the system the plug-in should be installed auto-matically. If the plug-in is not installed automatically, there are three ways to install the plug-inmanually: • Either install the plug-in from the CD as follows: 1. Close all unnecessary applications on your PC...

Page 14 - Documentation and Online Help

Documentation and Online Help Refer to the Avaya X330WAN Documentation and Utilities CD for full instructions.

Page 15 - Notes

Page 16 - Contact Information; From the United States:

Contact Information To contact Avaya technical support: From the United States: Please call 1-800-237-0016, press 0, then press 73300. From outside the United States: EMEA (Europe, Middle East and Africa). Email: [email protected] (Asia Pacific). Email: [email protected] CALA (Caribbean and Lat...