Page 2 - Important Safety Information; Installation
2 Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to t...
Page 3 - Service; Environmental Information
3 Do not use this hob if it is in contact with water. Do not operate the hob with wet hands.Ensure the control knobs are in the ‘OFF’ position when not in use.When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance.Unstable o...
Page 4 - Contents; Guide to Use the instructions
4 Contents Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an operation Hints and Tips Environmental information This appliance complies with the following E.E.C. Directives: -73...
Page 5 - Description of the Hob; WHEN THE HOB IS FIRST INSTALLED
5 Description of the Hob Installation Fig. 1 Any gas installation must be carried out by a registered CORGI installer, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual.Please, ensure that, once the hob is installed,...
Page 6 - Operation; Using the Wok Stand
6 Burner minimum maximum diameter diameter Triple-crown (ultra-rapid) 160 mm 260 mm Large (rapid) 160 mm 240 mm Medium (semi-rapid) 120 mm 220 mm Small (auxiliary) 80 mm 160 mm As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquidsimmering. If you use a sauce...
Page 7 - The Hob Top; Ignition electrode; Maintenance and Cleaning
7 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easilythan if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft clothwell wrun...
Page 8 - Something Not Working?
8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM There is no spark when lighting the gas The gas ring burns unevenly SOLUTION Check that the unit is plugged in and the electrical supply ...
Page 10 - Guarantee Conditions; Standard guarantee conditions; Exclusions; European Guarantee
10 Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any partthereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretionrepair or replace the same FREE O...
Page 11 - Instruction for the Installer; Engineers technical data; Supply Connections; Ignition HT Spark
11 Instruction for the Installer Engineers technical data B U R N E R R A P I D SEMI-RAPID A U X I L I A R Y TRIPLE (large) ( m e d i u m ) (small) C R O W N POSITION M A X M I N M A X M I N M A X M I N MAX MIN NOMINAL THERMALPOWER (kW) 2.8 0.65 2.0 0.45 1.0 0.33 4.0 1.2 NOMINAL FLOWRATE (m 3 /h) 0....
Page 12 - Important safety requirements; Location
12 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations(Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendationsare contained in the following British Standards Codes Of Practice: B.S. 6172/ B...
Page 13 - Important; Gas Connection
13 Installation Important This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI registered installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions i...
Page 14 - Cut Out Size; Building In; Building over a cupboard or drawer
14 560 150 min 48 0 FO 2038 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heatresistant board below the base of the hob on the underside of the...
Page 15 - Building over a kitchen unit with door
15 FO 2564 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET 1 FO 2563 2 Building over a kitchen unit with door Proper arrangements must be taken indesigning the furniture unit, in order to avoidany contact with the bottom of the hob whichcan be heated when it is operated. Therecommended solution ...
Page 16 - Fitting the Hob into the worktop; Seal
16 Fitting the Hob into the worktop Carry out the building in of the hob as follows: • p u t th e se al s supplied with the hob, onthe edges of the cut out:place them exactly on thefront and rear edge and at50 mm. from the sideedges, as shown in thediagram, taking care thatthe seals meet withoutover...
Page 17 - Electrical connections
17 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations.THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.T...
Page 19 - Fault Finding; Preliminary Electrical Systems Check
19 Fault Finding Preliminary Electrical Systems Check START Isolate applianceand carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supplyshould now besatisfactory. Carry out: D: Resistance to Earth check. Inlet wiringfaulty.Rectify anyfault. Isolat...
Page 21 - Ignition System / Gas Ignition
21 Check gas supply atburner Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fitting ofburners Check position of theelectrode Check by pass simmeradjusted...
Page 22 - Commissioning; Pressure Testing
22 Commissioning When the hob has been fully installed it will be necessary to checkthe minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several tim...
Page 23 - Conversion from Natural Gas to LPG; Method; To adjust the gas rate
23 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can beconverted for use with butane or propane gas providing the correct injectors are fitted.The gas rate is adjusted to suit. Method • Ensure that the gas taps are in the 'OFF' po...
