Page 2 - Important Safety Information; Installation; Child Safety; ENGLISH
2 Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation l This hob must be installed by qualified personnel, according to the manufacturers instructions and to...
Page 4 - Guide to Use the instructions; Contents; Instructions for the User
4 This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition. Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step ...
Page 5 - Description of the Hob; INSTALLATION; WHEN THE HOB IS FIRST INSTALLED
5 1. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Auxiliary Burner5. Control knob for back right burner (semi-rapid)6. Control knob for back left burner (semi-rapid)7. Control knob for front left burner (rapid)8. Control knob for front right burner (auxiliary) Description of the Hob INSTALLATION An...
Page 6 - Hob burners; Operation
6 Hob burners To light a burner: l turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner. Upon, ignition, adjust the flame as required. l If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, a...
Page 7 - The Hob Top; Pan Supports; The Burners; Maintenance and Cleaning
7 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wr...
Page 8 - Something Not Working?
8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM n There is no spark when lighting the gas n The gas ring burns unevenly SOLUTION u Check that the unit is plugged in and the electrical suppl...
Page 9 - Service and Spare Parts; Customer Care
9 Service and Spare Parts When you contact the Service Force Centre, they will need the following information: 1. Your name, address and post code.2. Your telephone number3. Clear and concise details of the fault4. The model and the serial number (see rating label on the back of this instruction boo...
Page 10 - Guarantee Conditions; European Guarantee
10 Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation.The guarantee do...
Page 11 - Instructions for the Installer; Engineers technical data
11 Overall dimensions Width: 580 mm. Depth: 500 mm. Cut out dimensions Width: 550 mm. Depth: 470 mm. Supply Connections Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. Ignition ...
Page 12 - Important safety requirements; Location
12 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/...
Page 14 - Gas Connection
14 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. It is import...
Page 15 - Cut Out Size; Building In; Building over a cupboard or drawer
15 550 470 580 500 55 min. FO 2291 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the undersid...
Page 17 - Fitting the hob to the worktop
17 Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. 1) Place the seali...
Page 18 - Electrical connections
18 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations.THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. ...
Page 19 - Permanent Connection; Wiring diagram; Replacement of the cable
19 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current...
Page 20 - Fault Finding; Preliminary Electrical Systems Check
20 Fault Finding Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supply should now be satisfactory. Carry out: D: Resistance to Earth check. Inlet wiring faulty. Rectify any fault. ...
Page 22 - Ignition System / Gas Ignition
22 Check gas supply at burner Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer a...
Page 23 - Commissioning; Pressure Testing
23 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite.2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several t...
Page 24 - Conversion from Natural Gas to LPG; Method; To adjust the gas rate
24 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit. Method 1) Ensure that the gas taps are in the 'O...
