Vision Fitness ST250 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Table of Contents:
Page 4 – T O O L S & P A R T S I N C L U D E D; P A R T S B O X
Page 5 – H A R D WA R E I N C L U D E D
Page 7 – B L A C K B A G
Page 8 – W E I G H T P L AT E S
Page 9 – O R A N G E B A G
Page 10 – B L U E B A G
Page 11 – P I N K B A G
Page 13 – G R E E N B A G
Page 15 – D E C A L S
Page 16 – s t a r t s; v i s i o n; w i t h a
Loading the manual
A s s e m b l y
G u i d e
ST250
LEG PRESS
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 4 - T O O L S & P A R T S I N C L U D E D; P A R T S B O X
4 19mm Wrench 6mm L-Shaped Wrench (2) T O O L S & P A R T S I N C L U D E D P A R T S B O X Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench
Page 5 - H A R D WA R E I N C L U D E D
5 O R A N G E B A G B L U E B A G H A R D WA R E I N C L U D E D M10 x 1.5P Nut Quantity: 12 10.5 x 18 x 2T Flat Washer Quantity: 16 M10 x 1.5P x 60L Carriage Bolt Quantity: 2 SW10.2 x 18.4 x 2.5T Spring Washer Quantity: 8 M10 x 1.5P x 100L Bolt Quantity: 4 M10 x 1.5P Nut Quantity: 3 M10 x 1.5P x 30...
Page 7 - B L A C K B A G
7 B L A C K B A G 15x33L Shoulder Bolt Quantity: 1 U Bracket Quantity: 1 M12 Slotted Bolt Quantity: 1 M10 x 1.5P Nut Quantity: 1 10.5 x 18 x 2T Flat Washer Quantity: 1 SW10.2 x 18.4 x 2.5T Spring Washer Quantity: 1 H A R D WA R E I N C L U D E D
Page 8 - W E I G H T P L AT E S
8 1 S T E P • If you aren’t adding any weightplates to the stack, skip this step andproceed to Step 2. • Your unit is equipped to handle 21-ten pound plates (20 plates andthe header plate). If you are addingplates to the stack after it has been inuse, proceed as follows: Loosen thenuts, attached to ...
Page 9 - O R A N G E B A G
9 1b 1a 1d 1c 1e 1e 2 S T E P • Attach the connecting brace (1a) tothe empty holes on the left floor support of the base unit ( ST200 ). Connect with two carriage bolts(M10x1.5Px60L), two flat (10.5x18x2T)& spring (SW10.2x18.4x2.5T) washers,and two nuts (M10x1.5P). Attach theopposite end of the ...
Page 10 - B L U E B A G
10 3 S T E P • Lay the seatback (2a) face down.Mate the seatback support (2b) to 2a.Make sure the holes of 2b are pointingup towards the top of the seatback.S e c u r e l y f a s t e n f o u r b o l t s(M10x1.5Px30L) into the seatbackusing a 6mm L-shaped wrench.Thread the pull pin partially into the...
Page 11 - P I N K B A G
11 4 S T E P • Insert the lever arm (3a) into the triangular structure at the front of 1b.When the holes are lined up, insert the9 0 m m s h a f t a l o n g w i t h a f l a t(17x25x1.5T) washer through the lowerend of 3a and fasten with a flat(10.5x30x2T) washer and a bolt(M10x1.5Px20L). Tighten fir...
Page 13 - G R E E N B A G
13 6 S T E P • Attach the pulley structure (U) to thebottom rear floor support of the baseunit with three bolts (M6x1Px15L), threeflat (6.4x14x1T), and three spring(SW6.1x12.2x1.5T) washers. Tightenwith a 4mm L-shaped wrench. • Slide pulley structure (Q) through theback side of the rear vertical sup...
Page 15 - D E C A L S
15 8 S T E P • Attach the decals according to the diagram below. D E C A L S P I N C H P O I N T S A F E T Y D E C A L P L A C E M E N T