Vision Fitness ST250 - Manuals

Page 4 - T O O L S & P A R T S I N C L U D E D; P A R T S B O X

4 19mm Wrench 6mm L-Shaped Wrench (2) T O O L S & P A R T S I N C L U D E D P A R T S B O X Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench

Page 5 - H A R D WA R E I N C L U D E D

5 O R A N G E B A G B L U E B A G H A R D WA R E I N C L U D E D M10 x 1.5P Nut Quantity: 12 10.5 x 18 x 2T Flat Washer Quantity: 16 M10 x 1.5P x 60L Carriage Bolt Quantity: 2 SW10.2 x 18.4 x 2.5T Spring Washer Quantity: 8 M10 x 1.5P x 100L Bolt Quantity: 4 M10 x 1.5P Nut Quantity: 3 M10 x 1.5P x 30...

Page 7 - B L A C K B A G

7 B L A C K B A G 15x33L Shoulder Bolt Quantity: 1 U Bracket Quantity: 1 M12 Slotted Bolt Quantity: 1 M10 x 1.5P Nut Quantity: 1 10.5 x 18 x 2T Flat Washer Quantity: 1 SW10.2 x 18.4 x 2.5T Spring Washer Quantity: 1 H A R D WA R E I N C L U D E D

Page 8 - W E I G H T P L AT E S

8 1 S T E P • If you aren’t adding any weightplates to the stack, skip this step andproceed to Step 2. • Your unit is equipped to handle 21-ten pound plates (20 plates andthe header plate). If you are addingplates to the stack after it has been inuse, proceed as follows: Loosen thenuts, attached to ...

Page 9 - O R A N G E B A G

9 1b 1a 1d 1c 1e 1e 2 S T E P • Attach the connecting brace (1a) tothe empty holes on the left floor support of the base unit ( ST200 ). Connect with two carriage bolts(M10x1.5Px60L), two flat (10.5x18x2T)& spring (SW10.2x18.4x2.5T) washers,and two nuts (M10x1.5P). Attach theopposite end of the ...

Page 10 - B L U E B A G

10 3 S T E P • Lay the seatback (2a) face down.Mate the seatback support (2b) to 2a.Make sure the holes of 2b are pointingup towards the top of the seatback.S e c u r e l y f a s t e n f o u r b o l t s(M10x1.5Px30L) into the seatbackusing a 6mm L-shaped wrench.Thread the pull pin partially into the...

Page 11 - P I N K B A G

11 4 S T E P • Insert the lever arm (3a) into the triangular structure at the front of 1b.When the holes are lined up, insert the9 0 m m s h a f t a l o n g w i t h a f l a t(17x25x1.5T) washer through the lowerend of 3a and fasten with a flat(10.5x30x2T) washer and a bolt(M10x1.5Px20L). Tighten fir...

Page 13 - G R E E N B A G

13 6 S T E P • Attach the pulley structure (U) to thebottom rear floor support of the baseunit with three bolts (M6x1Px15L), threeflat (6.4x14x1T), and three spring(SW6.1x12.2x1.5T) washers. Tightenwith a 4mm L-shaped wrench. • Slide pulley structure (Q) through theback side of the rear vertical sup...

Page 15 - D E C A L S

15 8 S T E P • Attach the decals according to the diagram below. D E C A L S P I N C H P O I N T S A F E T Y D E C A L P L A C E M E N T

Page 16 - s t a r t s; v i s i o n; w i t h a

5 0 0 S o u t h C P A v e n u e • P. O . B o x 2 8 0 • L a k e M i l l s . W I 5 3 5 5 1 t o l l f r e e 8 0 0 . 3 3 5 . 4 3 4 8 • p h o n e 9 2 0 . 6 4 8 . 4 0 9 0 • f a x 9 2 0 . 6 4 8 . 3 3 7 3 w w w. v i s i o n f i t n e s s . c o m © 2 0 0 5 V i s i o n F i t n e s s . A l l R i g h t s R e s ...