Vision Fitness ST760 - Manuals

Page 3 - T a b l e o f C o n t e n t s

3 ASSEMBLY GUIDE . . . . . . . . . . . . . . . . 4HARDWARE BAGS . . . . . . . . . . . . . . . . 6STEP 1: ORANGE BAG . . . . . . . . . . . . 10STEP 2: BLUE BAG . . . . . . . . . . . . . . . 11STEP 3: PINK BAG . . . . . . . . . . . . . . . 12STEP 4: GREEN BAG . . . . . . . . . . . . . . 13STEP 5: BLAC...

Page 4 - O w n e r ’ s G u i d e

4 To avoid possible damage to this Leg/Calf Press, please follow these assembly steps in the correct order. Before proceeding, find your new Leg/Calf Press serial number located on the back of the center floor support (AG2),and enter here: Refer to this number when calling for service, and enter thi...

Page 6 - H A R D WA R E I N C L U D E D

O R A N G E B A G 6 B L U E B A G H A R D WA R E I N C L U D E D 10.2 x 22 x 2 Flat Washer Quantity: 3 M10 Nylon Nut Quantity: 1 M10 x 120 Bolt Quantity: 1 10.2 x 22 x 2 Flat Washer Quantity: 16 M10 Nylon Nut Quantity: 8 M10 x 120 Bolt Quantity: 2 M10 x 48 Bolt Quantity: 2 M10 x 70 Bolt Quantity: 2 ...

Page 9 - R E D B A G

9 R E D B A G H A R D WA R E I N C L U D E D M10 x 25 Bolt Quantity: 8 Pull Pin Quantity: 1 10.2 x 22 x 2 Flat Washer Quantity: 4 M10 Nylon Nut Quantity: 2 M10 x 75 Bolt Quantity: 2

Page 10 - O R A N G E B A G

10 AC1 AC1 AG2 AG2 1 S T E P N O T E : During assembly, it is recommendedto ensure that all bolts are in place and partially threaded before completely tightening any one bolt. During assemblysteps 1 thru 4, do not completely tightenany bolts until completion of Step 4. • Lay the center floor suppor...

Page 11 - B L U E B A G

AC1 AC1 AG2 AG2 AG1 AG1 AB1 AB1 11 2 S T E P • Attach two pulleys to the weight stacktower (AB1) with two bolts (M10x48),four flat washers (10.2x22x2), and twonuts (M10). • Stand the weight stack tower (AB1) sothat it is upright, and place it next to the center floor support (AG2). Attach thetower t...

Page 12 - P I N K B A G

12 3 S T E P • Loosely secure top and bottom shieldbrackets (B10) to weight stack tower(AB1) using eight bolts (M5x10), eight flatwashers (5.2x10x1.5), and eight lockwashers (5.1x9.3x1.3) provided. Repeatfor all side brackets (B09). • Place two rubber weight plate bumpers(Z42) over the holes in the ...

Page 13 - G R E E N B A G

13 4 S T E P • Both swing arm covers (C13) must beplaced on the front of the main seat supportwith tallest sides facing rear of machine.Align bottom two holes on covers with thefront two holes along bottom edge of mainseat support (AC1). Attach using two bolts(M10x123), four flat washers (10.2x22x2)...

Page 14 - B L A C K B A G

14 5 S T E P • With the loop end of the cable in yourhand, guide it through hole in top of weightstack tower, and around pulleys A and B.Bring it down along the weight stack tower,through pulley C and around pulley D.Loosen or remove pulley D to be able toensure cable is routed between the post andt...

Page 15 - Y E L L O W B A G

15 6 S T E P • Align holes in rear shield (Q01) with theholes in the brackets on the back side ofthe weight stack tower (AB1); secure using10 bolts (M5x10). Take the left side shield(Q03) and repeat on front side of weightstack tower using six bolts (M5x10).Tighten interior brackets (B09 & B10)....

Page 16 - R E D B A G

16 AC1 AC1 AC2 AC2 AC3 AC3 AH1 AH1 7 S T E P • Attach handlebars (AC2 & AC3) to sideof main seat support (AC1) using two bolts(M10x75), four flat washers (10.2x22x2),two nylon nuts (M10). • Secure seat bottom to seat support usingfour bolts (M10x25). • Attach seat back to seat back post(AH1) usi...

Page 28 - s t a r t s; v i s i o n; w i t h a

5 0 0 S o u t h C P A v e n u e • P. O . B o x 2 8 0 • L a k e M i l l s . W I 5 3 5 5 1 t o l l f r e e 8 0 0 . 3 3 5 . 4 3 4 8 • p h o n e 9 2 0 . 6 4 8 . 4 0 9 0 • f a x 9 2 0 . 6 4 8 . 3 3 7 3 w w w. v i s i o n f i t n e s s . c o m © 2 0 0 7 V i s i o n F i t n e s s . A l l R i g h t s R e s ...