Page 2 - Complete this page for quick reference when service is required:; Date of Installation:; Information found on the data label:; Voltage
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: A E October, ...
Page 3 - Table of Contents
Table of Contents Model 161 Table of Contents Section 1 To the Installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Cooled Units 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric...
Page 5 - Air Cooled Units; Electrical Connections
1 Model 161 To the Installer 040211 Section 1 To the Installer This machine is designed for indoor use only. DO NOT install the machine in an area where a water jet could be used. Failure to follow this instruction may result in serious electrical shock. Air Cooled Units The Model 161 requires 6” (1...
Page 6 - Section 2; Compressor Warranty Disclaimer
2 Model 161 To the Operator 050818 Section 2 To the Operator The Model 161 soft serve freezer has been carefully engineered and manufactured to give you dependable operation.This unit, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, it w...
Page 8 - Section 4
4 Model 161 Operator Parts Identification Section 4 Operator Parts Identification Model 161 ITEM DESCRIPTION PART NO. 1 PANEL-REAR *161* 055129 2 PANEL-SIDE-RIGHT *161* 055130 3 LEG-4” 3/8-16 STUD 036397 4 CAP-RUBBER 037268 5 SHIELD-SPLASH 022765 6 TRAY-DRIP 16-7/8L X 5-1/8 020157 7 PANEL-LOWER FRON...
Page 9 - Beater Door Assembly
5 Model 161 Operator Parts Identification Beater Door Assembly ITEM DESCRIPTION PART NO. 1 DRAW VALVE 024763 2 O-- RING 7/8 OD X .103 W 014402 3 SEAL-- VALVE 030930 4 DOOR A.-- 3 SPOUT X30753-- SER 5 PIVOT PIN A.-- SHORT X38539 6 O-- RING 5/16 OD X .070 W 016272 7 DRAW VALVE HANDLE 030564 8 HAND SCR...
Page 10 - Accessories
6 Model 161 Operator Parts Identification Accessories ITEM DESCRIPTION PART NO. 1 PAIL-6·QT. 023348 2 BRUSH-REAR BRG 1” D X 2” LG 013071 3 BRUSH-DOUBLE·ENDED 013072 4 BRUSH-DRAW·VALVE·1” OD X2” X 17” 013073 ITEM DESCRIPTION PART NO. 5 BRUSH-MIX·PUMP·BODY-3”X7”WHITE 023316 6 LUBRICANT-TAYLOR·4·OZ. 04...
Page 11 - Section 5; Symbol Definitions
7 Model 161 Important: To the Operator Section 5 Important: To the Operator ITEM DESCRIPTION 1 POWER SWITCH 2 MIX REFRIGERATION KEY 3 STANDBY KEY 4 WASH KEY 5 AUTO KEY 6 INDICATOR LIGHT “MIX LOW” 7 RESET BUTTON Symbol Definitions To better communicate in the International arena, the words on many of...
Page 12 - Softech
8 Model 161 Important: To the Operator Softech t Control Machines Note: If your machine is not equipped with Softech t controls, please use the instructions on page 10. Power Switch When placed in the ON position, the power switch allows Softech t control panel operation. MIX REF When the MIX REF ke...
Page 13 - Air Tube
9 Model 161 Important: To the Operator If the beater motor is turning properly, press the WASH key to cancel the cycle. Press the AUTO key on both sides of the unit to resume normal operation. If the freezer shuts down again, contact a service technician. Air Tube The air tube serves two purposes. O...
Page 14 - Control Machines; Power Switch
10 Model 161 Important: To the Operator Non-- Softech t Control Machines Note: If your machine is equipped with the Softech t controls, please use the instructions on page 7. Push-Button Switch If an overload condition occurs, the freezer will automatically stop operating. To properly reset the free...
Page 15 - Section 6; Assembly
11 Model 161 Operating Procedures 040211 Section 6 Operating Procedures The Model 161 is a soft serve counter model with a three spout door. Two individual flavors are available from the end spouts, and an equal combination of both is dispensed through the center spout to create a twist effect. It h...
Page 18 - Sanitizing
14 Model 161 Operating Procedures Sanitizing Step 1 Prepare one gallon (3.8 liters) of an approved 100 PPM sanitizing solution (example: Kay-5 r ). USE WARM WATER AND FOLLOW THE MANUFACTUR- ER’S SPECIFICATIONS. Step 2 Pour the sanitizing solution into the hopper and allow it to flow into the freezin...
Page 19 - Priming
15 Model 161 Operating Procedures Step 5 Press the WASH key. This will cause the sanitizing solution in the freezing cylinder to be agitated. Allow it to agitate for five minutes. Figure 20 Note: Non--Softech t machines: Place the power switch in the WASH position. This will cause the sanitizing sol...
Page 20 - Closing Procedure
16 Model 161 Operating Procedures Step 3 Press the AUTO key. When the unit cycles off, the product will be ready to serve. Figure 24 Note: Non--Softech t machines: Place the power switch in the AUTO position. When the unit cycles off, the product will be ready to serve. Figure 25 Step 4 Momentarily ...
Page 21 - Draining Product From the; Rinsing; Cleaning
17 Model 161 Operating Procedures Draining Product From the Freezing Cylinder Step 1 Press the AUTO key to cancel operation. Press the MIX REF key to cancel hopper refrigeration. These operations should be cancelled as far ahead of cleaning time as possible. This will allow frozen product to soften ...
Page 22 - Disassembly; Brush Cleaning
18 Model 161 Operating Procedures Disassembly MAKE SURE THE POWER SWITCH IS IN THE “OFF” POSITION. Failure to follow this instruction may result in severe personal injury to fingers or hands from hazardous moving parts. Step 1 Remove the handscrews and the freezer door. Remove the beater assemblies ...
Page 23 - Section 7; During Cleaning and Sanitizing; Troubleshooting Bacterial Count
19 Model 161 Important: Operator Checklist Section 7 Important: Operator Checklist During Cleaning and Sanitizing ALWAYS FOLLOW LOCAL HEALTH CODES. Cleaning and sanitizing schedules are governed by your State or local regulatory agencies and must be followed accordingly. The following check points s...
Page 24 - Winter Storage
20 Model 161 Important: Operator Checklist j 6. If your machine is equipped with an auxiliary refrigeration system, check the auxiliary condenser for accumulation of dirt and lint. A dirty condenser will reduce the refrigeration capacity of the mix hopper. Condensers must be cleaned monthly with a s...
Page 25 - Section 8; PROBLEM
21 Model 161 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product being dispensed. a. The power switch is in the OFF position. a. Place the power switch in the AUTO position. 14 b. The mix level is inadequate in the mix hopper. b. Fill the mix h...
Page 28 - Section 9
24 Model 161 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY QTY. Beater Drive Shaft O-Ring X 2 Freezer Door O-Ring X 2 Freezer Door Front Bearing X 2 Freezer Door Guide Bearing X 2 Draw Valve O-Ring X 4 Center Draw Valve Seal X...
