Taylor 150 - Manual

2 Models 150, 152, 162, 168 To the Operator 050818 Section 2 To the Operator The freezer you have purchased has been careeru3n4s50818

4 Models 150, 152, 162, 168 Operator Parts Identification Section 4 Operator Parts Identification Model 150

10 Models 150, 152, 162, 168 Important: To the Operator Section 5 Important: To the Operator Figure 1 Item Description 1 Push Button Switch 2 Power Switch 3 Temperature Control 4 Mix Refrigeration Switch 5 Indicator Lights -- “Mix Low” Symbol Definitions To better communicate in the International ar...

11 Models 150, 152, 162, 168 Important: To the Operator Push-Button Switch If an overload condition occurs, the freezer will automatically stop operating. To properly reset the freezer, place the toggle switch in the “OFF” position. Wait two or three minutes; then press the push-button switch. Place...

12 Models 150, 152, 162, 168 Important: To the Operator Mix Refrigeration Switch The mix refrigeration switch is located under the control channel and is used for several purposes: 1. For the unit to operate in the “AUTO” mode, the mix refrigeration switch must be “ON”. 2. For the separate hopper re...

13 Models 150, 152, 162, 168 Operating Procedures Section 6 Operating Procedures The Model 150 has been selected to illustrate the pictured step-by-step operating procedures. All models in this manual are similar. They each have a 1.5 quart (1.4 liter) capacity freezing cylinder. The mix flows by gr...

14 Models 150, 152, 162, 168 Operating Procedures 060421 Assembly Note: When lubricating parts, use an approved food grade lubricant (example: Taylor Lube). Step 1 Install the beater assembly. Slide the small, thick o-ring into the groove on the drive shaft of the beater assembly. Apply an even coat...

17 Models 150, 152, 162, 168 Operating Procedures Note: Models 162/168 have three draw handles. Slide the tip of the draw handle into the slot of the draw valve, starting from the right. Slide the short pivot pin through the far right draw handle. Slide the long pivot pin through the far left and mi...

19 Models 150, 152, 162, 168 Operating Procedures 031030 Priming Prime the machine as close as possible to the time of first product draw. Step 1 With a pail beneath the door spout, raise the draw valve. Fill the mix hopper with fresh mix. (Maximum hopper capacity is 8 quarts [7.6 liters].) Allow th...

20 Models 150, 152, 162, 168 Operating Procedures Step 6 Slide the rear drip pan into the hole in the side panel. Figure 33 Closing Procedure To disassemble the Models 150/152/162/168, the following items will be needed: S Two cleaning pails S Sanitized stainless steel rerun can with lid S Necessary...

21 Models 150, 152, 162, 168 Operating Procedures When the solution stops flowing from the door spout, lower the draw valve and place the power switch in the “OFF” position. Repeat Steps 1 through 5 for the other side of the freezer on Models 162/168. Disassembly Step 1 BE SURE THE POWER SWITCH IS I...

22 Models 150, 152, 162, 168 Important: Operator Checklist 080107 Section 7 Important: Operator Checklist During Cleaning and Sanitizing ALWAYS FOLLOW LOCAL HEALTH CODES. Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly....

23 Models 150, 152, 162, 168 Important: Operator Checklist 051215 j 5. If your machine is air cooled, check the condenser for an accumulation of dirt and lint. A dirty condenser will reduce the efficiency and capacity of the machine. Condensers should be cleaned monthly with a soft brush. Never use ...

24 Models 150, 152, 162, 168 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product being dispensed. a. The power switch is in the “OFF” position. a. Place the power switch in the “AUTO” position. 19 b. The mix level is inadequate in the mix hoppe...

27 Models 150, 152, 162, 168 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY QTY. 150/152 162/168 Beater Drive Shaft O-Ring X 1 2 Freezer Door O-Ring X 1 2 Freezer Door Front Bearing X 1 2 Freezer Door Guide Bearing X 1 2 Draw V...