Taylor 142 - Manual

1 Model 142 To the Installer 131122 Section 1 To the Installer The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. Installer Safety In all areas of the world, equipment should be...

2 Model 142 To the Installer 101111 Electrical Connections In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA 70-1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising...

3 Model 142 To the Installer 130809 Electrical Hook- up Installation For 60 Cycle, 1 PH, Supplied With Cord and Plug This equipment is supplied with a 3- wire cord and grounding type plug for connection to a single phase, 60 cycle, branch circuit supply. This unit must be plugged into a properly gro...

4 Model 142 To the Operator 131122 Section 2 To the Operator Your freezer has been carefully engineered and manufactured to give you dependable operation. If the Taylor Model 142 is properly operated and cared for, it will produce a consistent, quality product. Like all mechanical products, this mac...

7 Model 142 Operator Parts Identification 140407 Section 4 Operator Parts Identification ITEM DESCRIPTION PART NO. 1 COVER A.- HOPPER X49633 2 FLOAT A.- MIX LEVEL X39690 3 TUBE- FEED- .166 HOLE- SS 035819 4 SHIELD- SPLASH- PLASTIC 039444 5 PAN A.- WHITE FRONT DRIP X43474 6 SEAL- U- CUP 080534 7 BEAT...

8 Model 142 Important: To the Operator Section 5 Important: To the Operator Figure 1 ITEM DESCRIPTION 1 Power Switch 2 Indicator Light - MIX LOW 3 Standby Switch Symbol Definitions To better communicate in the International arena, the words on many of our operator switches and buttons have symbols t...

9 Model 142 Important: To the Operator 130702 Standby Switch This push button switch determines which mode of operation the freezing cylinder is operating in. If the center button of this switch is in the “OUT” position and it is not illuminated, the unit will operate in the normal product dispensin...

10 Model 142 Operating Procedures 120501 Section 6 Operating Procedures The Model 142 has a 1.5 quart (1.4 liter) capacity freezing cylinder. The mix flows from the hopper to the freezing cylinder through a feed tube. The mix flow is controlled by gravity. We begin our instructions at the point wher...

13 Model 142 Operating Procedures 090421 The illustration below shows the draw valve assembled on the left side. Figure 16 Step 9 Snap the design cap over the bottom of the freezer door spout. Figure 17 Step 10 Lay the feed tube and mix level float in the bottom of the mix hopper. Sanitizing Step 1 ...

15 Model 142 Operating Procedures Priming Prime the machine as close as possible to the time of first product draw. Step 1 With a pail beneath the door spout, open the draw valve. Fill the mix hopper with FRESH mix and allow it to flow into the freezing cylinder. This will force out any remaining sa...

16 Model 142 Operating Procedures Standby This unit is equipped with a STANDBY feature. If product is not dispensed for long periods of time (i.e.; early morning hours), the STANDBY feature will maintain the hopper and freezing cylinder product at safe temperatures and prevent product breakdown. To ...

17 Model 142 Operating Procedures 140718 Draining Product From the Freezing Cylinder Step 1 Place the toggle switch in the OFF position as far ahead of cleaning time as possible to allow frozen product to soften for easier cleaning. Step 2 Lift the hopper cover, remove the feed tube and the mix leve...

18 Model 142 Operating Procedures 120529 Brush Cleaning Step 1 Prepare a sink with an approved cleaning solution (ex- amples: Kay- 5 R or Stera- Sheen R ). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. ( IMPORTANT: Follow the label directions. A STRONG solution can cause parts dam- ag...

19 Model 142 Important: Operator Checklist 080110 Section 7 Important: Operator Checklist During Cleaning and Sanitizing: Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the unit has a “Standby mode”, it must not be...

20 Model 142 Important: Operator Checklist Winter Storage If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is subject to freezing conditions.Disconnect the freezer from the main po...

21 Model 142 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product being dispensed. a. Toggle switch in OFF position. a. Place toggle switch in the AUTO position. 15 b. Inadequate level of mix in mix hopper. b. Fill mix hopper with mix. 15 c. Bea...

23 Model 142 Parts Replacement Schedule 120430 Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY QUANTITIES TO BE REPLACED Beater Drive Shaft Cup Seal X 1 Freezer Door O- Ring X 1 Freezer Door Front Bearing X 1 Freezer Door Guide Bearing X 1 Draw Valve O- R...

24 Model 142 Limited Warranty on Equipment 131122 Section 10 Limited Warranty on Equipment TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor-branded freezer equipment a...

26 Model 142 Limited Warranty on Parts 131122 Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacement com...