Page 2 - Complete this page for quick reference when service is required:; Date of Installation:; Information found on the data label:; Voltage; 003 Carrier Commercial Refrigeration, Inc.; Taylor Company; a division of Carrier Commercial Refrigeration, Inc.
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: A E 2003 Carr...
Page 3 - Table of Contents
Table of Contents Model C706 Table of Contents Section 1 To the Installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 2 To the Operator 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 3 Safety 5 . ....
Page 4 - Table of Contents - Page 2; civil and criminal penalties.
Table of Contents Model C706 Table of Contents - Page 2 Cleaning 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembly 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 5 - Installer Safety
1 Model C706 To the Installer 131122 Section 1 To the Installer The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. Installer Safety In all areas of the world, equipment should b...
Page 7 - To the Installer; Beater Rotation; Note: The following procedures should be; Refrigerant
3 Model C706 To the Installer 130809 Supply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve co...
Page 8 - To the Operator; Section 2; Compressor Warranty Disclaimer; only the refrigerant specified on the affixed data
4 Model C706 To the Operator 131122 Section 2 To the Operator The Model C706 has been carefully engineered and manufactured to give you dependable operation. This unit, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, it will require clea...
Page 11 - Operator Parts Identification; Section 4; Figure 1
7 Model C706 Operator Parts Identification 140625 Section 4 Operator Parts Identification Figure 1 ITEM DESCRIPTION PART NO. 1 KIT A.- COVER- HOPPER X65368- SP 2 PAN- DRIP 11- 5/8 LONG 027503 3 PIN- RETAINING- HOPPER COVER 043934 4 PANEL- SIDE- LEFT 066722- SP2 5 STUD- NOSE CONE 055987 6 SHIELD- SPL...
Page 12 - Model C706 Single Spout Door and Beater Assembly; Figure 2
8 Model C706 Operator Parts Identification 110509 Model C706 Single Spout Door and Beater Assembly Figure 2 ITEM DESCRIPTION PART NO. 1 DOOR A.- W/BAFFLE X56071- SER 2 HANDLE A.-DRAW-WELDED X56246 3 SCREW-ADJUSTMENT-5/16-24 056332 4 O-RING-1/4 OD X .070W 50 015872 5 PIN - HANDLE - S.S. 055819 6 PLUG...
Page 13 - Figure 3
9 Model C706 Operator Parts Identification 140625 X57029- XX Pump A. - Mix Simplified Figure 3 ITEM DESCRIPTION PART NO. 1- 7 PUMP A.- MIX SIMPLIFIED S.S.- COMPLETE X57029- 14 1 CYLINDER- PUMP HOPPER SOFTSERVE 057943 2 PIN A.- RETAINING X55450 3 PISTON- PUMP- SIMPLIFIED 053526 4 O- RING- 2- 1/8 OD X...
Page 14 - Accessories; Figure 4
10 Model C706 Operator Parts Identification 140717 Accessories Figure 4 ITEM DESCRIPTION PART NO. 1 TOOL-O-RING REMOVAL 048260-WHT 2 BRUSH-REAR·BRG·1IN.DX2IN. 013071 3 BRUSH-DOUBLE·ENDED 013072 4 BRUSH-DRAW·VALVE·1”ODX2 013073 5 BRUSH-MIX·PUMP·BODY-3”X7 023316 6 SANITIZER STERA SHEEN(JAR) 010425-CS ...
Page 15 - Important: To the Operator; Section 5; Figure 5
11 Model C706 Important: To the Operator 041118 Section 5 Important: To the Operator C706 Figure 5 ITEM DESCRIPTION 1 MIX LOW INDICATOR LIGHT 2 MIX OUT INDICATOR LIGHT 3 MIX REFRIGERATION KEY 4 STANDBY KEY 5 WASH KEY 6 AUTO KEY ITEM DESCRIPTION 7 PUMP KEY 8 RESET BUTTON - BEATER MOTOR 9 RESET BUTTON...
Page 16 - Symbol Definitions; end without the hole
12 Model C706 Important: To the Operator Symbol Definitions To better communicate in the International arena, symbols have replaced words on many of our operator switches, function, and fault indicators. Your Taylor equipment is designed with these International symbols. The following chart identifi...
Page 18 - Long “No Sale” Periods
14 Model C706 Important: To the Operator 050126 Feed Tube (Back- up Option) If the air/mix pump has become inoperable because of a missing or damaged part, the operator can temporarily operate the unit using the feed tube. The product ejection rate will be slower when the feed tube is used instead o...
Page 19 - Operating Procedures; Section 6; Assembly; MAKE SURE POWER SWITCH IS IN THE
15 Model C706 Operating Procedures 080714 Section 6 Operating Procedures The C706 unit stores mix in a hopper. The mix is pumped into the freezing cylinder. It has a 3.4 quart (3.2 liter) capacity freezing cylinder and a 20 quart (18.9 liter) mix hopper. We begin our instructions at the point where ...
Page 22 - Mix Hopper Assembly
18 Model C706 Operating Procedures 041118 Step 8 Install the front drip tray and the splash shield under the door spout. Figure 18 Step 9 Slide the rear drip pan into the hole in the side panel. Slide the pump drip pan into the hole in the back panel. Figure 19 Mix Hopper Assembly Step 1 Inspect the...
Page 25 - Sanitizing; Note: You have just sanitized the mix hopper and
21 Model C706 Operating Procedures 080714 Step 13 Slide the large black o- ring and the two smaller black o- rings into the grooves on the drive shaft. Thoroughly lubricate the o- rings and shaft. DO NOT lubricate the hex end of the shaft. (See Figure 31.) Figure 31 Step 14 Install the hex end of th...
Page 27 - Priming; fresh
23 Model C706 Operating Procedures 050126 Step 8 When a steady stream of sanitizing solution is flowing from the prime plug opening in the bottom of the freezer door, pull the draw handle down. Draw off all of the sanitizing solution. Figure 38 Step 9 Once the sanitizer stops flowing from the door s...
Page 28 - Closing Procedure
24 Model C706 Operating Procedures 041118 Step 2 Once a steady stream of mix starts to flow from the prime plug opening in the bottom of the freezer door, push down the prime plug. Figure 41 Step 3 When the mix stops bubbling down into the freezing cylinder, insert the mix feed tube. Remove the lock...
Page 29 - Draining Product From the; If local health codes permit the use of rerun; Rinsing; cool; Cleaning
25 Model C706 Operating Procedures 140717 Draining Product From the Freezing Cylinder Step 1 Press the AUTO key, cancelling compressor and beater motor operation. Press the MIX REF key, cancelling the mix hopper refrigeration system. Step 2 Remove the hopper cover and take it to the sink for cleanin...
Page 30 - Disassembly; Be sure the power switch is in the OFF; Brush Cleaning
26 Model C706 Operating Procedures 080714 Disassembly Step 1 Be sure the power switch is in the OFF position. No lights should be illuminated on the control panel. Note: Failure to follow this instruction may result in severe personal injury to fingers or hands from hazardous moving parts. Step 2 Re...
Page 31 - For proper brush cleaning of the adapter, cap,
27 Model C706 Operating Procedures 030102 Note: For proper brush cleaning of the adapter, cap, feed tube, and orifice, refer to the following illustration which indicates proper brush usage.Rinse all parts with clean, warm water. Place the pump parts on a clean, dry surface. Step 8 Wipe clean all ex...
Page 32 - During Cleaning and Sanitizing; CLEANING AND SANITIZING MUST BE; Troubleshooting Bacterial Count
28 Model C706 Important: Operator Checklist 071205 Section 7 Important: Operator Checklist During Cleaning and Sanitizing Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the unit has a “Standby mode”, it must not be...
Page 34 - Troubleshooting Guide; Section 8; PROBLEM
30 Model C706 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product is being dispensed with draw valve open and the machine in the AUTO mode. a. Freeze- up in mix inlet hole. a. Call service technician to adjust the mix hopper temperature. - - - ...
Page 38 - Parts Replacement Schedule; Section 9
34 Model C706 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY Drive Shaft Seal X Scraper Blade X Freezer Door Gasket X Front Bearing X Beater Shoes X Draw Valve O- Ring X Prime Plug O- Ring X Feed Tube O- Ring X Air Orifice O- R...
Page 39 - Limited Warranty on Equipment
35 Model C706 Limited Warranty on Equipment 131122 Section 10 Limited Warranty on Equipment TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor-branded freezer equipment ...
Page 41 - Limited Warranty on Parts; TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS; No warranty; LIMITED WARRANTY CONDITIONS; location in the unit of original installation.
37 Model C706 Limited Warranty on Parts 131122 Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacement co...
Page 43 - The owner; must
39 Model C706 Limited Warranty on Parts LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNE...
