South Bend SB1269 - Manual
South Bend SB1269 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Identification
- Page 3 – Inventory; Qty; Unpacking; For Assembly
- Page 4 – Basic steps for removing rust preventative:; Cleaning & Protecting
- Page 5 – Installation; To install the taper attachment:
- Page 10 – Operation; To use the taper attachment:
- Page 11 – To disable the taper attachment:
- Page 12 – To clean the taper attachment:; Maintenance Schedule; To lubricate the taper attachment:
- Page 13 – Taper Attachment Breakdown
- Page 14 – Parts List
MODEL SB1269
TAPER ATTACHMENT
Instruction Sheet
This taper attachment is heavy! Get
assistance when installing this accessory on
the lathe. Wear heavy duty leather boots for
foot and toe protection, and keep hands and
fingers away from all pinch points. Ignoring
this warning can lead to a severe crushing
injury or finger amputation!
•
Fits Lathe Models ..14" x 40" SB1012, SB1013
................................ 16" x 60" SB1014, SB1015
............................... 16" x 40" SB1037, SB1038
•
Taper Per Inch Range .............................0–18"
•
Minor Inch Scale Divisions ....................0.010"
•
Major Inch Scale Divisions ....................0.020"
•
Taper Angle Range .................................0–10°
•
Minor Taper Scale Divisions .......................
1
⁄
2
°
•
Major Taper Scale Divisions.........................1°
•
Maximum Length of Taper ..................... 12
1
⁄
4
"
•
Taper Adjustment Knob ............................ Yes
•
Construction .............................................Steel
•
Unit Weight ............................................ 78 lbs
•
Origin ................................................... Taiwan
The Model SB1269 taper attachment was
designed to fit onto a series of South Bend
lathes. Shown in Figure 1, is a Model SB1012
lathe that is fitted with the Model SB1269 taper
attachment.
Figure 1. Model SB1269 installed.
Taper attachment installed
on rear side of lathe
Introduction
If you need help with your new item, contact
us at: (360) 734-1540
•
FAX: (360) 676-1075
This taper attachment mounts quickly to the
back bed way of your lathe. Accurate tapers of up
to 12" can be produced without repositioning the
attachment or having to offset the talstock.
The Model SB1269 features scales at both ends,
reading inches-per-foot and degrees. An angle
adjusting knob with fine threads achieves
exacting control when setting tapers.
Another feature is the ability to use the taper
attachment without disengaging the cross slide
nut. This design allows the taper attachment to
be functional at any time by simply tightening
the two deadman-clamp cap screws, which lock
the deadman-clamp to the rear lathe way.
Specifications
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Identification Serious personal injury could occur if you connect the lathe to power before completing the installation process. DO NOT connect power until instructed to do so later in this manual. Untrained users have an increased risk of seriously injuring themselves with this lathe accessory. Do ...
Inventory When you are completely satisfied with the condition of your shipment, you should inventory the contents. Inventory (Figure 3) Qty A. Cap Screws M10-1.5 x 40mm (Taper Attachment Mounting) ...................... 4 B. Taper Attachment Assembly ......................... 1 C. Tapered Pins 8.7 ...
The unpainted surfaces are coated with a heavy- duty rust preventative that prevents corrosion during shipment and storage. This rust preventative has been a close ally and guardian since this item left the factory. If the unpainted surfaces are free of rust, then be thankful that the rust preventat...
