South Bend SB1269 - Manuals

Page 2 - Identification

Identification Serious personal injury could occur if you connect the lathe to power before completing the installation process. DO NOT connect power until instructed to do so later in this manual. Untrained users have an increased risk of seriously injuring themselves with this lathe accessory. Do ...

Page 3 - Inventory; Qty; Unpacking; For Assembly

Inventory When you are completely satisfied with the condition of your shipment, you should inventory the contents. Inventory (Figure 3) Qty A. Cap Screws M10-1.5 x 40mm (Taper Attachment Mounting) ...................... 4 B. Taper Attachment Assembly ......................... 1 C. Tapered Pins 8.7 ...

Page 4 - Basic steps for removing rust preventative:; Cleaning & Protecting

The unpainted surfaces are coated with a heavy- duty rust preventative that prevents corrosion during shipment and storage. This rust preventative has been a close ally and guardian since this item left the factory. If the unpainted surfaces are free of rust, then be thankful that the rust preventat...

Page 5 - Installation; To install the taper attachment:

Installation To install the taper attachment: 1. DISCONNECT LATHE FROM POWER! 2. With the assistance of a helper and using a 6mm hex wrench, remove the four cap screws holding the splash guard on the rear of the lathe. 3. Using a 5mm hex wrench, remove the two leadscrew end-cap cap screws shown in F...

Page 10 - Operation; To use the taper attachment:

Operation 6. Retighten both dovetail lock cap screws. 7. Begin lathe operations. When the deadman clamp cap screws are loose, the deadman clamp slides along the lathe way, and the taper attachment is disengaged. Normal lathe turning operations can be conducted. When the deadman clamp cap screws are ...

Page 11 - To disable the taper attachment:

To disable the taper attachment: 1. DISCONNECT LATHE FROM POWER! 2. Use an 8mm hex wrench, and loosen both deadman clamp cap screws shown in Figure 26, so the deadman can slide on the way as the carriage is moved. Figure 27. Taper angle control knob. Dovetail Lock Cap Screw Taper Angle Control Knob ...

Page 12 - To clean the taper attachment:; Maintenance Schedule; To lubricate the taper attachment:

3. Using an oil can with the same oil you use on your lathe ball oilers, apply oil on the knob threads shown in Figure 30. To clean the taper attachment: 1. DISCONNECT LATHE FROM POWER! 2. Vacuum excess metal chips and wipe off the remaining metal, coolant, and oils with a dry cloth. If any coolant ...

Page 13 - Taper Attachment Breakdown

2 9 8 7 3 33 32 31 30 28 12 13 5 2 21 20 18 17 16 15 14 12 13 12 11 10 34 35 27 26 36 25 22 24 36 23 19 20 51 10 11 48 46 47 33 45 44 43 40 42 40 39 38 37 23 41 46 49 50 Taper Attachment Breakdown For Product Mfg. Since 1/10 Model SB1269 -13- P A R T S

Page 14 - Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION 2 PCAP02M CAP SCREW M6-1 X 20 28 PSB1269028 PIN 3 PSB1269003 BALL OILER 30 PSB1269030 PIVOT SADDLE 5 PSB1269005 END CAP 31 PSB1269031 GIB 7 PFH04M FLAT HD SCR M6-1 X 8 32 PSB1269032 GIB SCREW 8 PSB1269008 COVER PLATE 33 PCAP31M CAP SCREW M8-1.25 X 25 9 P...