South Bend HDC-24 - Manuals

H EAVY D UTY C OUNTERLINE S PECIFICATIONS O WNER ’ S M ANUAL 1192662 P AGE 5 SPEC IFICATI O NS CLEARANCES ! WARNING There must be adequate clearance between units and adjacent construction. Clearance must also be provided for servicing and for operation. Measure back clearance from rear of 2" st...

I NSTALLATION H EAVY D UTY C OUNTERLINE P AGE 6 O WNER ’ S M ANUAL 1192662 INSTALLATION I N S T A L L A T I O N NOTICE Installation must comply with National Fuel Gas Code, ANSI Z223.1 , Natural Gas Installation Code, CAN/CGA-B149.1 , or the Propane Installation Code, CAN/CGA-B149.2 , as applicable....

H EAVY D UTY C OUNTERLINE I NSTALLATION O WNER ’ S M ANUAL 1192662 P AGE 7 INSTALLATION Step 2a: Installation on Countertop Legs To install the appliance using countertop legs, do the following: 1. Locate the box of four legs shipped with the appliance (if countertop legs were ordered). 2. Raise the...

I NSTALLATION H EAVY D UTY C OUNTERLINE P AGE 8 O WNER ’ S M ANUAL 1192662 INSTALLATION Step 3: Attach Restraint for Appliances Mounted on Casters NOTICE For an appliance equipped with casters, (1) the installation shall be made with a connector that complies with the Standard for Connectors for Mov...

H EAVY D UTY C OUNTERLINE I NSTALLATION O WNER ’ S M ANUAL 1192662 P AGE 9 INSTALLATION Appliances mounted on a stand with casters or other movable surface must be equipped with a restraining means to prevent accidental stress on the flexible gas connection. 1. Secure the restraining-device bracket ...

I NSTALLATION H EAVY D UTY C OUNTERLINE P AGE 10 O WNER ’ S M ANUAL 1192662 INSTALLATION Step 4: Connect Gas Supply The serial plate is located interior side of the control panel (see Figure 1 on page 3). It indicates the type of gas the appliance is equipped to burn. All Southbend equipment is adju...

H EAVY D UTY C OUNTERLINE I NSTALLATION O WNER ’ S M ANUAL 1192662 P AGE 11 INSTALLATION Figure 4 Vent tu be included on griddles built aft er June 19, 2006. Step 5: Final Positioning, Clearance Check, and Ventilation Check 1. Position the appliance where it will be operated. 2. Check that the appli...

I NSTALLATION H EAVY D UTY C OUNTERLINE P AGE 12 O WNER ’ S M ANUAL 1192662 INSTALLATION 2. Light all the griddle burners. For griddles with thermostatic controls, turn all knobs to 200°F for one hour. For griddles with manual controls, turn all knobs to “LOW” for one hour. Then gradually bring each...

H EAVY D UTY C OUNTERLINE O PERATION O WNER ’ S M ANUAL 1192662 P AGE 13 OPERATION O P E R A T I O N ! DANGER EXPLOSION HAZARD Purchaser of equipment must post in a prominent location, detailed instructions to be followed in the event the operator smells gas. Obtain the instructions from the local g...

O PERATION H EAVY D UTY C OUNTERLINE O RP E ATI ON OPERATION OF THERMOSTATIC GRIDDLE MODELS Each 12"-wide griddle section has a thermostatic-control knob on the front panel that directly controls the flow of gas, and so the heat. Turn the knob clockwise to increase the heat; turn it counterclock...

H EAVY D UTY C OUNTERLINE O PERATION O WNER ’ S M ANUAL 1192662 P AGE 15 OPERATION OPERATION OF MANUAL GRIDDLE MODELS Each 12"-wide griddle section has a knob on the front panel that directly controls the flow of gas, and so the heat. Turn the knob clockwise to increase the heat; turn it counter...

O PERATION H EAVY D UTY C OUNTERLINE P AGE 16 O WNER ’ S M ANUAL 1192662 OPERATION OPERATION OF CHARBROILER MODELS Each 6"-wide charbroiler section has a knob on the front panel that directly controls the flow of gas, and so the heat. Turn the knob counterclockwise to increase the heat; turn it ...

H EAVY D UTY C OUNTERLINE O PERATION O WNER ’ S M ANUAL 1192662 P AGE 17 OPERATION OPERATION OF OPEN-TOP BURNER MODELS Each 12"-wide open-top burner section has two knobs on the front panel that directly control the flow of gas to the section’s two burners, and so control the heat. Turn a knob c...

C LEANING H EAVY D UTY C OUNTERLINE P AGE 18 O WNER ’ S M ANUAL 1192662 CLEANING C L E A N I N G Southbend equipment is constructed with the best quality materials and is designed to provide durable service when properly maintained. To expect the best performance, your equipment must be maintained i...

A DJUSTMENTS H EAVY D UTY C OUNTERLINE P AGE 20 O WNER ’ S M ANUAL 1192662 ADJUSTMENT S A D J U S T M E N T S ! WARNING ADJUSTMENTS AND SERVICE WORK MAY BE PERFORMED ONLY BY A QUALIFIED TECHNICIAN WHO IS EXPERIENCED IN, AND KNOWLEDGEABLE WITH, THE OPERATION OF COMMERCIAL COOKING EQUIPMENT. HOWEVER, ...

H EAVY D UTY C OUNTERLINE A DJUSTMENTS O WNER ’ S M ANUAL 1192662 P AGE 21 ADJUSTMENT S ADJUSTMENT OF PILOT FLAME (GRIDDLE MODELS) The pilots are adjusted at the factory. If later the pilots are over-adjusted to the point where the flame is leaving its port, or “blowing off,” the result is an unstab...

A DJUSTMENTS H EAVY D UTY C OUNTERLINE A S DJU TM EN TS ADJUSTMENT OF BURNER FLAME The burners are adjusted at the factory. If necessary to adjust the burner flames, do the following for each burner: 1. Turn the burner’s control knob to the full ON position. 2. If the appliance was cold, wait 5 minu...

H EAVY D UTY C OUNTERLINE A DJUSTMENTS O WNER ’ S M ANUAL 1192662 P AGE 23 ADJUSTMENT S ADJUSTMENT OF GRIDDLE THERMOSTATS Each burner’s control knob operates a snap-action thermostatic valve that was adjusted at the factory. If the griddle surface temperature is different from the thermostat dial se...

T ROUBLESHOOTING H EAVY D UTY C OUNTERLINE P AGE 24 O WNER ’ S M ANUAL 1192662 TROUBLESHOOTING T R O U B L E S H O O T I N G Consult the following table for troubleshooting guidance. Problem Look for - No burners or pilots will turn on – Main gas supply to unit is “OFF” Problem with a particular bur...

H EAVY D UTY C OUNTERLINE P AGE 26 O WNER ’ S M ANUAL 1192662 HEAVY DUTY COUNTERLINE A product with the Southbend name incorporates the best in durability and low maintenance. We all recognize, however, that replacement parts and occasional professional service may be necessary to extend the useful ...