South Bend sb1016 - Manuals

SAFETY For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -11- S A F E T Y Understanding Risks of Machinery Operating all machinery and machining equipment can be dangerous or relatively safe depending on how it is installed and maintained, and the operator's experience, common sense, risk awarenes...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -13- S A F E T Y Additional Metal Lathe Safety 7. Speed Rates: Operating the lathe at the wrong speed can cause nearby parts to break or the workpiece to come loose, which will result in dangerous projectiles that could cause severe impact injury. ...

PREPARATION -14- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P R E P A R A T I O N Preparation Overview Things You'll Need To complete the preparation process, you will need the following items: For Lifting and Moving s 4WOEXTRAPERSONSWITHGUIDERODSTOSTEADY the lathe during lifting and moving...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -15- P R E P A R A T I O N Power Supply Requirements Electrocution or fire may occur if machine is not correctly grounded and attached to the power supply. Use a qualified electrician to ensure a safe power connection. Before installing the machine...

-16- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P R E P A R A T I O N Correcting Phase Polarity (Yaskawa Drive) This sub-section is only provided for troubleshooting by a qualified electrician. If you discover during the test run that the lathe will not operate, or that one or more motors r...

-18- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P R E P A R A T I O N Inventory Main Inventory 1: (Figure 6) Qty A. Steady Rest Assembly .................................... 1 B. D1-8 Camlock Stud Set .................................. 1 C. 15" Faceplate w/D1-8 Camlock Stud Set ...... 1...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -19- P R E P A R A T I O N The unpainted surfaces are coated at the factory with a heavy-duty rust preventative that prevents corrosion during shipment and storage.The benefit of this rust preventative is that it works very well. The downside is tha...

-20- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P R E P A R A T I O N Lathe Electrical Access Door = Power Connection Location 131" Min. 30" Wall Keep Workpiece Loading Area Unobstructed 62" 147" 18" Figure 8. Space required for full range of movement. Physical Environme...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -21- P R E P A R A T I O N Lifting & Moving Do not attempt to lift or move this lathe if you do not have the proper equipment or the necessary assistance from other people. All lifting equipment must be rated for at least 10,000 lbs. to account...

-22- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P R E P A R A T I O N Leveling & Mounting You must level your machine and either use the included foot pads and leveling hardware or bolt your lathe to the floor. Because mounting your lathe to the f loor with permanent hardware is an opti...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -23- P R E P A R A T I O N Assembly With the exception of the handwheel handles, the lathe is shipped fully assembled. To install the handwheel handles, thread the large handle into the carriage handwheel and the small handle into the cross slide h...

-24- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P R E P A R A T I O N Connecting to Power Due to the complexity required for planning, bending, and installing the conduit necessary for a code-compliant hardwire setup, an electrician or other qualified person MUST perform this type of instal...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -25- P R E P A R A T I O N Test Run After all preparation steps have been completed, the machine and its safety features must be tested to ensure correct operation. If you discover a problem with the operation of the machine or its safety component...

-30- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P R E P A R A T I O N NEVER attempt to shift the headstock or quick change gearbox when the lathe is in operation. Gear clash causing tooth damage will result. Only use the gear shifting levers when the spindle id stopped. 8. Turn the lathe ON...

OPERATION For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -31- O P E R A T I O N Operation Overview Loose hair, clothing, or jewelry could get caught in machinery and cause serious injury or death. Keep these items away from moving parts at all times to reduce this risk. During operation, small ...

-32- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N Refer to the following figures and descriptions to learn about the basic controls of this machine. Main Power Control A. Master Power Switch: The rotary switch shown in Figure 37 toggles incoming power ON/OFF to the lathe. It...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -33- O P E R A T I O N K. Cutting Fluid Pump Switch: Start/stops the cutting fluid pump motor. L. Jog Button: Turns the spindle motor ON while being pressed and held. M. Stop Button: Stops all machine functions. Twist clockwise to reset. N. Carriag...

-34- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N AH. Tailstock Lock Bolt: Tightens a secondary tailstock clamp to assist the primary tailstock lock lever and clamp. AI. Offset Scale: Indicates the distance of tailstock offset from the spindle centerline with arbitrary marks...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -35- O P E R A T I O N Foot Brake This lathe is equipped with a foot brake ( Figure 45 ) to quickly stop the spindle. Pushing the foot brake while the spindle is ON cuts power to the motor and stops the spindle. Once stopped, the spindle lever MUST...

-36- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N 3. One at a time, use the chuck key to turn each of the camlocks counterclockwise until the cam line aligns with the cam release datum line, as shown in Figure 47 . As you turn the camlocks, they will rise up slightly from th...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -39- O P E R A T I O N 3-Jaw Chuck Refer to Chuck & Faceplate Mounting instructions on Page 35 to mount the 3-jaw chuck to the spindle. The 3-jaw scroll-type chuck included with this lathe features hardened steel jaws that center the workpiece....

-40- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N — If installed correctly, the jaws converge together at the center of the chuck. — If the jaws do not come together, the initial thread was missed on one of the jaws. Remove all the jaws and start again. Mounting Workpiece It...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -41- O P E R A T I O N 6. After the workpiece is held in place by the jaws, turn the chuck by hand and pay attention to the workpiece alignment. — If the workpiece is not correctly aligned for your operation, turn the chuck and make fine adjustment...

-42- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N The tailstock can be offset from the spindle centerline for turning tapers. The offset movement is controlled by two opposing cap screws on the front and back sides of the tailstock (see Figure 63 ). Figure 63. Offsetting cap...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -43- O P E R A T I O N However, other tooling without lock tangs, such as the remaining four shown in Figure 66 , can still be used if the following two conditions exist: 1. If the potential torque load from smaller drill chucks, drill bits, and ce...

-44- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N Aligning The offset of your lathe was aligned with the spindle centerline at the factory. We recommend that you take the time to ensure that the tailstock is aligned to your own desired tolerances, especially if you have chan...

-46- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N Faceplate Refer to Chuck & Faceplate Mounting instructions on Page 35 to mount the faceplate to the spindle. The 15" faceplate included with your lathe offers a wide range of uses, including machining non-concentric w...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -47- O P E R A T I O N Mounting Center in Spindle 1. DISCONNECT LATHE FROM POWER! 2. Thoroughly clean and dry the tapered mating surfaces of the spindle bore, tapered sleeve, and the center, making sure that no lint or oil remains on the tapers. 3....

-48- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N Mounting Center in Tailstock Either the carbide-tipped dead center or a live center can be mounted in the tailstock. Mounting instructions are the same for both. To mount a center in the tailstock: 1. DISCONNECT LATHE FROM PO...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -49- O P E R A T I O N 5. Close the steady rest and tighten the lock knob. 6. Loosen the three leaf screws. Without causing any deflection in the workpiece, use the finger adjustment knobs to position the finger rollers against the workpiece. 7. Ti...

-50- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N The 4-way tool post is mounted on top of the compound slide, and allows a maximum of four tools to be loaded simultaneously. Quick indexing to different tools is accomplished by loosening the top handle, rotating the tool pos...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -51- O P E R A T I O N Tools Needed Qty Tool Post T-Wrench ............................................... 1Steel Shim ............................................. As NeededCutting Tool ........................................................... 1...

-52- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N Manual Feed These three handwheels (see Figure 83 ) manually position and control the cutting tool for lathe operations. Carriage Handwheel Moves the carriage parallel along the ways, and is equipped with a graduated collar i...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -53- O P E R A T I O N Figure 87. Spindle speed range lever. Setting Spindle Speed 5. Turn the spindle ON , and slowly turn the spindle speed dial to your calculated spindle speed. Figure 88. Quick change range lever. If using the quick change gear...

-54- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N Power Feed Controls The headstock feed direction lever shown in Figure 89 controls the direction the carriage moves. However, it is important to understand that there is a direction change relationship between the headstock f...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -55- O P E R A T I O N If the threading or general carriage feed is required, the carriage lock (see Figure 91 ) must be disengaged. If the cross feed will be used for facing, the carriage lock should be engaged and the cross feed gib lock screw (s...

-56- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N Half Nut Lever The half nut lever locks the carriage to the leadscrew which moves the cutting tool along the length of the workpiece ( Figures 93 – 94) . When threading, we recommend using the slowest speed possible and avoid...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -57- O P E R A T I O N Using Thread Dial and Chart Find the TPI (threads per inch) that you want to cut in the left column (see Figure 96 ), then reference the dial number to the right of it. The dial numbers indicate when to engage the half nut fo...

-58- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N Other Fractional TPI Select one position and always return to that single position on the thread dial for cutting the TPI shown in Figure 101 . Typically 1 on the thread dial is selected for ease of memory. Figure 101. Number...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -59- O P E R A T I O N Understanding Thread & Feed Rate Chart A complete threading and feed rate chart is located on the face of the headstock that shows all available threading and feed configurations for your lathe. Chart use is described bel...

-60- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 O P E R A T I O N Repositioning Change Gears The factory has arranged the change gears in the "normal position" so all inch and metric threading and feed selections are available by shifting levers. However, if modular or diametral pit...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -61- O P E R A T I O N To use the cutting fluid system on your lathe: 1. Make sure the tank is properly serviced and filled with cutting fluid, and that you wear the necessary personal protection equipment. 2. Position the cutting fluid nozzle for y...

-62- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 A C C E S S O R I E S Accessories This section includes the most common accessories available for your lathe, which may be available through your local South Bend Lathe Co. dealer. If you do not have a dealer in your area, please call us at (3...

MAINTENANCE -64- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 M A I N T E N A N C E Always disconnect power to the machine before performing maintenance. Failure to do this may result in electrocution or accidental startup injury. ! Maintenance Schedule Typically, each operator is responsible...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -65- M A I N T E N A N C E South Bend La the Co . ® Monthly Maintenance Char t for EVS T oolroom Series L athes 123456789 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 0 3 1 Lubrication Ways Ball Oilers Leadscrew...

-66- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 M A I N T E N A N C E Lubrication Headstock The headstock has a pressurized lubrication system that consists of an oil pump, a low oil pressure kill switch, a supply tank, oil hoses, and a manifold with oil distribution lines. The headstock ha...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -67- M A I N T E N A N C E Checking & Adding Oil Oil Type...Mobil DTE Light or ISO 32 EquivalentOil Amount .............................................. 4 GallonsCheck/Add Frequency .................................... DailyChange Frequency .....

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -69- M A I N T E N A N C E Priming the Oil Pump The lubrication system is also equipped with a check valve that is shown in Figure 121 . This valve allows oil to flow to the headstock during pump operation, but prevents the oil from draining back i...

-70- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 M A I N T E N A N C E Apron Oil Type ...... Mobil Vactra 2 or ISO 68 EquivalentOil Amount ............................................ As NeededCheck/Add Frequency .................................... DailyChange Frequency .......................

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -71- M A I N T E N A N C E Unpainted & Machined Surfaces Besides the ways and leadscrew, all other unpainted and machined surfaces should be wiped down daily to keep them rust-free and in top condition. This includes the top of the saddle, the ...

-72- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 M A I N T E N A N C E Change Gears Grease Type ............................................... NLGI#2Frequency ................ Annually or When Swapping The change gears, shown in Figure 130 , should always have a thin coat of heavy grease to...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -73- M A I N T E N A N C E Cutting Fluid System The cutting fluid system holds 6 1 ⁄ 2 gallons. A pump pulls fluid from the tank and sends it to the valve, which controls the flow of cutting fluid through a universal hose and nozzle. When the valve...

-74- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 M A I N T E N A N C E Changing Cutting Fluid When you replace the old cutting fluid, take the time to thoroughly clean out the chip drawer, catch tray, and chip drawer. Make sure to dispose of all old fluid according to local regulations. Cutt...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -75- M A I N T E N A N C E 8. Pour out the remaining cutting fluid from the tank into the 5-gallon bucket and seal the bucket with its lid. 9. Lift and slide the tank out far enough for cleaning. 10. Using mineral spirits and rags, clean and dry th...

-76- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 M A I N T E N A N C E Machine Storage If the machine is not properly prepared for storage, it may develop rust or corrosion. If decommissioning this machine, use the steps in this section to ensure that it remains in good condition for later u...

SERVICE For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -77- S E R V I C E Backlash Adjustment Figure 136. Cross slide backlash adjustment screws. Cap Screw Set Screw Cross Slide Leadscrew Tools Needed: Qty Hex Wrench 3mm ................................................. 1Hex Wrench 6mm ...........

-78- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 S E R V I C E After a long period of time, you may find that the leadscrew develops a small amount of end play. This lathe is designed so that leadscrew end play can be easily removed with adjustment. Tools Needed: Qty Open End Wrench 36mm or ...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -79- S E R V I C E Saddle Gibs The saddle on this lathe is equipped with opposing gibs that lie parallel with one another on either side of the saddle. To tighten the saddle and remove play, the front gib must move toward the tailstock, and the rea...

-80- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 S E R V I C E Half Nut Adjustment The half nut mechanism can be tightened if it becomes loose from wear. The pressure exerted by the half nut is controlled by a gib. The half nut gib is adjusted with two set screws. Tool Needed: Qty Hex Wrench...

-82- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 S E R V I C E Brake Inspection & Replacement The linkage geometry on this lathe is non adjustable. Before replacing the brake shoes, verify that all fasteners are tight, and all clevis pins and yokes have minimal wear. As pivot points wear...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -85- S E R V I C E Leadscrew Shear Pin Replacement 3. Rotate the shroud washer so the cutout in the washer aligns with the shear pin head, as shown in Figure 154 . 4. Put on safety glasses. 5. Slide the retaining ring away from the shroud washer so...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -87- S E R V I C E The gap insert was installed, then ground flush with the bed at the factory to ensure precise fit and alignment. Therefore, if removed, it may be difficult to re-install with the same degree of alignment and mating when installed...

TROUBLESHOOTING -88- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 W A R R A N T Y If you need replacement parts, or if you are unsure how to do any of the solutions given here, feel free to call us at (360) 734-1540. Symptom Possible Cause Possible Solution Machine does not start or a circuit...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -91- E L E C T R I C A L ELECTRICAL Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section ca...

-92- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 E L E C T R I C A L Wiring Overview Spindle Motor,Page 97. Cutting FluidPump Motor, Page 99. Oil PumpMotor,Page 98. Oil PressureSwitch, Page 98. End Gear Cover Safety Switch, Page 102. Brake Limit SafetySwitch, Page 102. SpindleON/OFF Switch,P...

-96- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 E L E C T R I C A L Fig. 163. Electrical box. SB1016/36 Electrical Box box photo

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -103- P A R T S Headstock Controls 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 21 22 23 24 25 26 28 29 30 32 34 35 36 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 1 1 2 3 4 5 6 7 8 9 10 11 12 29 8 34 29 32 PARTS

-104- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Headstock Controls Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSB10160001 SHIFTING SHAFT END CAP 29 PSB10160029 STEP PIN 2 PSB10160002 SHIFTING LEVER 30 PSB10160030 LONG SHIFTING ROD 3 PCAP38M CAP SCREW M5-.8 X 25 32...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -105- P A R T S Headstock Internal Gears 101 102 103 104 105 106 107 108 109 110 111 112 113 123 124 A D E A F F A D E C A D D C E E F F 106 114 115 116 117 118 119 120 121 122 125 126 127 128 129 130 131 132 133 134 135 136 138 139 140 141 142 143...

-106- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Headstock Internal Gears Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 101 PSB10160101 CAM LOCK STUD D1-8 134 PR32M EXT RETAINING RING 48MM 102 PSB10160102 SPINDLE NOSE CAP SCREW 135 PSB10160135 GEAR 32T 103 PSB10160103 S...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -107- P A R T S Headstock Transfer Gears C B G H I J L K M C B G H I J L K M 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 214 215 216 217 218 186 187 188 122 194 187 188 143 194 194 187 188...

-108- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Headstock Transfer Gears Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 116 PSB10160116 KEY 10 X 8 X 36 197 PSB10160197 GEAR 24T 122 PCAP14M CAP SCREW M8-1.25 X 20 198 PSB10160198 SQUARE HD OIL DRAIN PLUG 1/2 PT 128 PR38M ...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -109- P A R T S Gearbox Gears G1 G1 G2 G2 G3 G3 G3 G2 G1 G1 G2 G3 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 34...

-110- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Gearbox Gears Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 301 PSB10160301 OUTBOARD GEAR SHAFT G1 339 PSB10160339 THRUST WASHER 302 PK109M KEY 7 X 7 X 35 340 PSB10160340 GEAR 24T 303 PSB10160303 THRUST WASHER 341 PSB1016...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -111- P A R T S Gearbox Controls A 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 429 431 373 373 377

-112- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Gearbox Controls B 373 374 375 376 377 378 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 430 432 376 385 385

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -113- P A R T S Gearbox Controls Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 373 PSB10160373 STEP PIN LOCK WASHER 402 PSB10160402 SHIFT SELECTOR SUPPORT 374 PSB10160374 SHOULDER PLATE 403 PSB10160403 SHIFT SELECTOR PLUNGER 375 PSB10160...

-114- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Apron Front H B D A B C D E H F H G F E D C B A G 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 540 541 542 543 545 546 547 548 549 550 55...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -115- P A R T S Apron Rear H 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622...

-116- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Apron Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 501 PSB10160501 HANDWHEEL HANDLE BOLT 547 PSB10160547 LEVER ASSEMBLY 502 PSB10160502 HANDWHEEL HANDLE 548 PORP021 O-RING 20.8 X 2.4 P21 503 PSS12M SET SCREW M6-1 X 25 54...

-118- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Compound Slide & Tool Post 701 702 703 704 705 706 707 708 709 710 712 713 714 715 716 717 718 719 722 723 724 725 726 727 728 729 730 732 733 734 736A 716 714 723 714 725 REF PART # DESCRIPTION REF PART # DESCRIPTION 701 PSB101...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -119- P A R T S Cross Slide & Saddle A 801 802 803 804 805 806 807 808 811 812A 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 864 858 859 860 874 861 862 801 863 ...

-120- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Cross Slide & Saddle B 846 847 848 849 850 851 852 853 854 855 856 857 868 847 849 Viewed From Underneath Saddle X

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -121- P A R T S Cross Slide & Saddle Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 801 PSB10160801 GIB ADJUSTMENT SCREW 838 PSB10160838 HANDWHEEL END CAP 802 PSB10160802 CROSS SLIDE 839 PSB10160839 HANDWHEEL HANDLE 803 PSB10160803 CO...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -123- P A R T S Bed & Shafts Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 901 PSB10160901 BED 938 PSB10160938 COMPRESSION SPRING 902 PSB10160902 GAP INSERT 939 PSTB003 STEEL BALL 3/8 903 PN09M HEX NUT M12-1.75 940 PCAP84M CAP SCREW ...

-124- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S End Gears 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1009 1008 1006 1007 1001 1002 1006 1006 REF PART # DESCRIPTION REF PART # DESCRIPTION 1001 PB176MM HEX BOLT M12-1.75 X 25 BLK C12.9 1010 ...

-126- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Motor & Lubrication Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1101 PSB10161101 STRAIGHT PIPE ADAPTER 1 PT X 3/4" 1131-1 PSB10161131-1 MOTOR FAN COVER 1102 PSB10161102 HOSE CLAMP 1" 1131-2 PSB10161131-2 MOT...

-128- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Cabinets & Panels Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1201 PSB10161201 BRAKE PEDAL SHAFT 1231 PSB10161231 CHUCK GUARD 1202 PSB10161202 BRAKE PEDAL 1232 PCAP26M CAP SCREW M6-1 X 12 1203 PSB10161203 LOCK COLLA...

-130- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Tailstock Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1301 PSB10161301 HANDWHEEL HANDLE SCREW 1324 PN29M HEX NUT M18-2.5 1302 PSB10161302 HANDWHEEL HANDLE 1325 PW18M FLAT WASHER 18MM 1303 PSS19M SET SCREW M8-1.25 X 30 1...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -131- P A R T S Thread Dial 1401 1402 1403 1404 1405 1407 1408 1409 1410 1411 REF PART # DESCRIPTION 1401 PSB10161401 INDICATOR PLATE 1402 PSB10161402 GEAR SHAFT 1403 PSB10161403 DIAL INDICATOR CASTING 1404 PSB10161404 KNURLED KNOB 1405 PSB10161405...

-134- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Brake System 1601 1602 1604A 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1620 1621 1623 1624 1625 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1629 REF PART # DESCRIPTION REF PART # DESCRIPTION 1601 PSB1016...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -135- P A R T S Electrical Cabinet & Control Panel Control Panel Electrical Cabinet 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1717 1718 1719 1720 1721 1722 1723 1705 1707 1707 1711 1715 1715 1716 1724

-136- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Electrical Cabinet & Control Panel Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1702 PSB10161702 CIRCUIT BREAKER AB SP3D320 20A 1713 PSB10132209 OL RELAY AB 193TAB10 0.6-1.0A (SB1036) 1703 PSB10161703 MAIN POWER SWIT...

-138- For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 P A R T S Front Machine Labels 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1903 1904 REF PART # DESCRIPTION REF PART # DESCRIPTION 1901 PSB10161901 MACHINE ID LABEL (SB1016) 1913 PSB10161913 SADDL...

For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -139- P A R T S The safety labels provided with your machine are used to make the operator aware of the machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of these safety labels...

WARRANTY & RETURNS For Machines Mfg. Since 7/ 09 Model SB1016 / SB1036 -141- W A R R A N T Y This quality product is warranted by South Bend Lathe Company to the original buyer for one year from the date of purchase. This warranty does not apply to consumable parts, or defects due to any kind of...