Shop Fox M1013 - Manual - manualsarea.com

Page 3 - LG

J<K LG <C< : K I @: 8 C D 8 @EK< E8E: < J<I M @:< G8I K J FG< I 8 K@FEJ J8= < K P @EKI F;L: K@FE LJ<K?<HL@:B>L@;<G8><C89<CJKFJ<8I:?FLK@E=FID8K@FE=8JK :fek\ekj @EKIF;L:K@FE%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% ) Woodstock Technical Support .............

Page 4 - If you have comments about this manual, please contact us at:

-2- D('(*Fne\ijDXelXcD]^%J`eZ\-&'0 @EKI F;L: K@FE Nff[jkfZbK\Z_e`ZXcJlggfik This machine has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation. Woodstock In...

Page 12 - Hkp

-10- D('(*Fne\ijDXelXcD]^%J`eZ\-&'0 J< K L G B\\g dXZ_`e\ [`jZfee\Zk\[ ]ifdgfn\ilek`c`ejkilZk\[fk_\in`j\% This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. L...

Page 13 - kf

-11- D('(*Fne\ijDXelXcD]^%J`eZ\-&'0 J<K L G =cffiCfX[1 This machine distributes a heavy load in a small footprint. Some residential floors may require additional bracing to support both machine and operator. Nfib`e^:c\XiXeZ\j1 Consider existing and anticipated needs, size of material to b...

Page 17 - Jkfg

-15- D('(*Fne\ijDXelXcD]^%J`eZ\-&'0 J<K L G :_`gKiXp:Xjk@ife Jkfg The chip tray directs small workpieces into a bucket when the cut is complete. The cast iron stop allows you to repeat cuts at the same length. Kf`ejkXcck_\Z_`gkiXpXe[ZXjk`ifejkfg#[fk_\j\jk\gj1 (% Position the chip tray, as sho...

Page 24 - FG

-22- D('(*Fne\ijDXelXcD]^%J`eZ\-&'0 FG < I 8 K@FEJ ,% Adjust the cast iron stop for duplicate cuts and install the ejector chute if required. -% Loosen the headstock lock lever ( =`^li\)+ ), and swivel the headstock to the needed angle of cut, and lock the lever in place. .% Set the blade gui...

Page 26 - Measure the material thickness. This

-24- D('(*Fne\ijDXelXcD]^%J`eZ\-&'0 FG < I 8 K@FEJ 9cX[\J\c\Zk`fe The chart below is a basic starting point for choosing blade type based on teeth per inch (TPI) for variable tooth pitch blades and for standard raker type bimetal blades/HSS blades. However, for exact specifications of bandsaw...

Page 32 - WIRING DIAGRAM COLOR KEY

-30- D('(*Fne\ijDXelXcD]^%J`eZ\-&'0 J<I M @:< These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Study this diagram carefully. If you notice differences between your machine and these wir...

Page 33 - JKFG; wiring diagram

-31- D('(*Fne\ijDXelXcD]^%J`eZ\-&'0 J<I M @:< 9Xe[jXnDfkfi <c\Zki`ZXc9fo 9Xe[jXnDfkfi :XgXZ`kfi:fm\i :XgXZ`kfi Dfkfi I\[ 9cXZb >iXp P\ccfn N_`k\ >i\\e 9cXZb L oad Neutr al Gr ound (('M Gfn\iJlggcp N_`k\ 9cXZb *4I\[ (49cXZb +4>iXp )4P\ccfn Wire number Wire Color (('M :fee\Zk`fe ...

Page 42 - guides and shafts

-40- D('(*Fne\ijDXelXcD]^%J`eZ\-&'0 G8 I K J >l`[\jJ_X]kj *() *(' *'0 *'0 *'. *', *'/ *'- *). *** **+ *)+ **' **( *)- *). *)) *)* *)0 *(/ **, **) *(. *(0 *(* *'0 *)* *)- *). *). *)+ *)) **, *(/ *(. *(, *(- **+ *** *'*M) *'+ *')M) *'(M) **0 *+' *''M) **0 guides and shafts

Page 46 - Place

TAPE ALONG EDGES--PLEASE DO NOT STAPLE FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE NFF;JKF:B@EK<IE8K@FE8C@E:%G%F%9FO)*'09<CC@E>?8D#N80/)).$)*'0 Place Stamp Here

Shop Fox M1013 - Manual

Table of Contents:

Summary

Other Shop Fox Models