Page 3 - Contents
SE T U P EL EC TR IC A L M A IN TE N A N CE SE RV IC E PA RT S O PE R AT IO N S SA FE T Y IN TR O DU CT IO N USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST! Contents INTRODUCTION .................................................................................................. 3 Wood...
Page 5 - Woodstock Technical Support; About Your New 16-Speed Drill Press; INTRODUCTION
-3- M1102/M1103 16-Speed Drill Press IN TR O DU CT IO N Woodstock Technical Support We stand behind our machines! In the event that questions arise about your machine, parts are miss- ing, or a defect is found, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail...
Page 7 - Identification
-5- M1102/M1103 16-Speed Drill Press IN TR O DU CT IO N Identification Figure 1. Drill press features and controls. Refer to the list below and see Figure 1 to become familiar with the drill press controls. 1. Light Switch: Turns light ON/OFF . 2. Power Switch: Turns motor ON/OFF . 3. Depth Stop: Li...
Page 8 - For Your Own Safety, Read Instruction Manual; NOTICE; Safety Instructions for Machinery; SAFETY
-6- M1102/M1103 16-Speed Drill Press SA FE T Y 1. READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents seri- ous injury hazards to untrained users. 2. ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eye- glasses only have impact resistant lenses—the...
Page 10 - Safety for Drill Presses
-8- M1102/M1103 16-Speed Drill Press SA FE T Y 1. EYE/FACE/HAND PROTECTION. A face shield used with safety glasses is recommended. Always keep hands and fingers away from the drill bit. Never hold a workpiece by hand while drilling! DO NOT wear gloves when operating the drill. 2. GUARD. Only use thi...
Page 11 - ELECTRICAL; Extension Cords
-9- M1102/M1103 16-Speed Drill Press EL EC TR IC A L ELECTRICAL 110V Operation We do not recommend using an extension cord for equip- ment. Instead, arrange the placement of your machinery and installed wiring to eliminate the need for extension cords. If you must use an extension cord, please use t...
Page 12 - Unpacking; SET UP; Inventory
-10- M1102/M1103 16-Speed Drill Press SE T U P Your drill press has been carefully packaged for safe transporting. If you notice the machine has been dam- aged, please contact your authorized SHOP FOX ® dealer immediately. Unpacking SET UP Note: Some parts and hardware may already be installed on th...
Page 14 - Table Support; Column and Base
-12- M1102/M1103 16-Speed Drill Press SE T U P Table Support The table support must be installed as described to prop- erly assemble your drill press. To install the table support: 1. Check to make sure the pinion is inserted into the table support, as shown in Figure 4 , so the pinion and gear teet...
Page 16 - Headstock
-14- M1102/M1103 16-Speed Drill Press SE T U P The headstock must be mounted on the column/base assembly before the drill press can be operated. Moving and installing the headstock is a two-person job. Headstock To install the headstock, do these steps: 1. Loosen the two set screws on the right side...
Page 17 - Chuck Guard
-15- M1102/M1103 16-Speed Drill Press SE T U P The drill chuck attaches to the spindle by means of the arbor, shown in Figure 12 . Matched tapers on the arbor and the inside of the chuck create a semi-permanent assembly when properly joined. When the drill press is shipped from the factory, a plasti...
Page 19 - Downfeed Handles & Belt
-17- M1102/M1103 16-Speed Drill Press SE T U P Figure 15. Downfeed handles and belt cover knob installed. The downfeed handles must be installed to properly oper- ate the drill press. To install the downfeed handles, do these steps: 1. Thread the knobs onto the handles, then thread the handles into ...
Page 21 - Mounting
-19- M1102/M1103 16-Speed Drill Press SE T U P The Model M1102 must be secured to a bench. The Model M1103 base should be secured to the floor, or bolted to a mobile base. Bench Mounting To mount the Model M1102 drill press to a table: 1. Clamp the base on a bench top capable of hold- ing approximat...
Page 22 - OPERATIONS; General; Installing & Removing
-20- M1102/M1103 16-Speed Drill Press O PE R AT IO N S OPERATIONS General DO NOT investigate problems or adjust the Drill Press while it is running. Wait until the machine is turned OFF , unplugged and all working parts have come to a complete stop before proceeding! The Model M1102/M1103 will perfo...
Page 23 - Changing Spindle RPM
-21- M1102/M1103 16-Speed Drill Press O PE R AT IO N S Figure 21. Loosening lock knob. The belts in the headstock must be rearranged to change spindle RPM. A chart under the pulley cover shows the belt positions needed to make the drill press run at the desired RPM. For example, the pulley ratio sho...
Page 24 - Depth Stop
-22- M1102/M1103 16-Speed Drill Press O PE R AT IO N S Figure 22. Depth stop components. Jam Nut Depth Nut Depth Stop Stud The Model M1102/M1103 has a depth stop that allows you to drill repeated non-through holes to the same depth every time. The depth stop consists of a stud attached to the quill ...
Page 27 - Arbor Removal
-25- M1102/M1103 16-Speed Drill Press O PE R AT IO N S Figure 24. Inner and outer drift-key slots aligned. Both Slots Aligned The arbor can be removed to install another drill chuck in the spindle. A drift key is included to help remove the arbor from the spindle. Usually, once the chuck and arbor h...
Page 28 - Table and Base; MAINTENANCE
-26- M1102/M1103 16-Speed Drill Press M A IN TE N A N CE V-Belts Inspect regularly for tension and wear. Check pulleys to ensure that they are properly aligned. Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. DO NOT lubricate them. ...
Page 29 - SERVICE; Troubleshooting
-27- M1102/M1103 16-Speed Drill Press SE RV IC E SERVICE Symptom Possible Cause Possible Solution Machine does not start or a breaker trips. 1. Plug or receptacle is at fault or wired incor- rectly. 2. Start capacitor is faulty.3. Motor connection is wired incorrectly.4. Power supply is faulty, or i...
Page 32 - Feed Shaft Spring
-30- M1102/M1103 16-Speed Drill Press SE RV IC E Feed Shaft Spring Tension The feed shaft return spring is adjusted at the factory; however, during the life of the drill press you may want to adjust the feed shaft return spring so the pressure suits your operating needs. Figure 26. Feed shaft return...
Page 33 - Electrical Components
-31- M1102/M1103 16-Speed Drill Press SE RV IC E Electrical Components Figure 30. Light socket with dust plug removed. Light Switch Power Switch Figure 28. Power and light switch assembly. Figure 29. Capacitor. Light Socket Capacitor
Page 34 - PARTS
-32- M1102/M1103 16-Speed Drill Press SE RV IC E Wiring Diagram PARTS 110V Wiring Diagram M1102/M1103 ����������������� ���� ����� ������ ���������� ������ ����� ��������� ��������������� ����������� �������������� ��������� ����������� ���� ������������������������������������ ���������������������...
Page 35 - Service Notes
-33- M1102/M1103 16-Speed Drill Press SE RV IC E Service Notes
Page 39 - Label Placement and Parts
-37- M1102/M1103 16-Speed Drill Press PA RT S REF PART � # DESCRIPTION 191 XLABEL01H SAFETY�GLASSES�LABEL 192 XLABEL03 CLOSE�COVER�LABEL 193 XM1102193 MACHINE�DATA�LABEL�(M1102) 193 XM1103193 MACHINE�DATA�LABEL�(M1103) 194 XM1102194 SHOP�FOX�LOGO�PLATE 195 XLABEL04S ELECTRICAL�LABEL 196 XM1102196 MO...
Page 40 - Parts Notes
-38- M1102/M1103 16-Speed Drill Press PA RT S Parts Notes
Page 41 - Warranty
M1102/M1103 16-Speed Drill Press Warranty Woodstock International, Inc. warrants all SHOP FOX ® machinery to be free of defects from work- manship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or...
Page 42 - Warranty Registration
CUT ALONG DOTTED LINE Name ___________________________________________________________________________________Street __________________________________________________________________________________City _________________________ State ___________________________ Zip ________________________Phone # ...
