Samsung VR30T80313W - User Manual

P REP ARA TION • For information on Samsung’s environmental commitments and product regulatory obligations, e.g. REACH, visit our sustainability page available via www.samsung.com Docking Station • Do not modify the polarized plug to fit a non-polarized outlet or extension cord. • Do not use outdoor...

P REP ARA TION Jet Bot • Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc. • Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on. • Do not put any objects into o...

P REP ARA TION Power related WARNING • Please prevent any risk of electric shock or fire. – Do not damage the power cord. – Do not pull the power cord too hard or touch the power plug with wet hands. – Do not use a power source other than rated volatge of the charger and also do not use a multi-outl...

P REP ARA TION • Be sure the Jet Bot does not suck in or touch any kind of liquids (water, beverage, filth, etc.). – The Jet Bot can be severely damaged and it may contaminate other areas if the wheels pass through liquid. • Do not spill any liquids on the Docking Station. – There is a risk of fire ...

P REP ARA TION In use WARNING • If any abnormal sounds, smells or smoke come from the Jet Bot, immediately shut off the power switch of the Jet Bot and contact a service center. CAUTION • Using the Jet Bot on a thick carpet may damage both the Jet Bot and the carpet. – The Jet Bot cannot pass over a...

P REP ARA TION Cleaning and maintenance WARNING • When the power cord is damaged, contact a service center to get it replaced by a certified repairman. – There is a risk of fire or electric shock. • Please check with a SAMSUNG Electronics service center when replacing batteries. – Using batteries fr...

INSTALLA TION INSTALLATION Installing a Docking Station Approximately 0.5 m Approximately 0.5 m Approximately 1m 1 Connect the provided Battery Charger jack to the rear of the Docking Station. 2 Position the Battery Charger cord into the fixing groove at the rear of the Docking Station. 3 Connect th...

OPERA TION Charging the Jet Bot Before using the Jet Bot for the first time, charge it completely. (For the charging time and cleaning time, refer to the ‘Product specification’.) 1 Open the upper cover of the Jet Bot and remove the white gasket. OFF ON 2 Remove the yellow gasket attached to the pow...

OPERA TION Auto charging The Jet Bot automatically returns to the Docking Station when it completes cleaning or when the battery is low to recharge. Docking (Recharging) You can return the Jet Bot to the Docking Station while cleaning to recharge. • Press the [ ] on the Jet Bot or use the SmartThing...

OPERA TION Checking if the docking (recharging) does not work Check the Docking Station’s installation status. • Check whether the Docking Station has been installed in a place where the Docking Station cannot guide the Jet Bot to return. • Check whether the distance between the Docking Station and ...

OPERA TION Using the Jet Bot Before using the Jet Bot, press the power switch at the side of the Jet Bot to turn the Jet Bot on. ❇ ❇ For the normal use of the Jet Bot’s functions, the SmartThings connection is required. – For downloading and installing the SmartThings App, refer to the ‘SmartThings ...

OPERA TION Operation status on the LED Status Indicator Classification Color Meaning Jet Bot While operating Red Blinking without moving An error occurs. Blinking while moving Auto returning to the Docking Station due to low battery On Operating stops due to low battery While charging Red, orange, o...

OPERA TION Cleaning Functions Cleaning Functions Operation Cleaning Methods • Auto Clean: Cleans automatically until the Jet Bot completes cleaning all rooms one time. • Room Clean: You can select a room you want to clean.• Spot Clean: You can set a specific area you want to clean. Cleaning Mode • Y...

OPERA TION Additional functions Additional functions Operation Energy-Saving Mode • When charging is complete, the Jet Bot automatically enters the Sleep Mode. While the Jet Bot is docked on the Docking Station, press and hold the [ ] for 7 seconds to set it to the Sleep Mode. To cancel the Sleep Mo...

OPERA TION Attaching Boundary Markers If Boundary Markers are attached before using the Jet Bot, the Jet Bot can operate safely. You can purchase additional Boundary Markers at a service center. To prevent the Jet Bot from entering the following areas, attach the Boundary Markers to the floor in a s...

OPERA TION Parts diagram Jet Bot 03 02 01 06 08 05 09 04 07 Top 01 Obstacle Sensor 02 Power switch 03 LiDAR Sensor 04 Dustbin 05 Start/stop button 06 Docking (Recharging) button 07 Status Indicator 08 Docking Sensor Window 09 Upper Cover 04 01 07 02 06 05 03 04 08 09 04 Bottom 01 Charging Pin 02 Bru...

MAINTENANCE Cleaning the Jet Bot Before maintenance work, you should turn off the power switch at the side of the Jet Bot. Emptying and cleaning the Dustbin 1 Grasp the Jet Bot’s cover at the groove and lift it up. 2 Hold the Dustbin handle and lift the Dustbin up. 3 Unlock the transparent clip at t...

MAINTENANCE Cleaning the brush 1 Push the Brush Cover Lock to the right to unlock. 2 Detach the brush cover. 3 Lift up the left side of the brush first and then pull the brush from the groove on the right. 4 Clean the brush. 5 Attach the brush. 6 Attach the brush cover. English 24 1_DJ68-00857F-03_I...

MAINTENANCE Cleaning the Sensor Window Wipe the Sensor Window with a soft cloth. Docking Sensor Window Obstacle Sensor Rear Sensor LiDAR Sensor Cliff Sensor Dust Sensor Cleaning the Driving Wheel 1 Place a soft cloth down first, turn the Jet Bot over, and place it gently on the cloth. 2 Remove forei...

MAINTENANCE Cleaning the Side Brush Cover the Side Brush with a hot steamed cloth for 10 seconds, then wipe the Side Brush. When the Side Brush is very tangled with hair, threads, etc., detach the Side Brush with a screwdriver while gripping the Side Brush, and remove the foreign matter. If the Side...

APPENDIX SmartThings App The SmartThings App is only compatible with models that have a Wi-Fi function.If you do not have a Wi-Fi router, you cannot use the SmartThings App. Setting up the wireless router • Please refer to the user manual of your wireless router for the settings of the wireless rout...

APPENDIX Downloading the SmartThings App • Download and install the SmartThings App from the markets (Google Play Store, Apple App Store, or SAMSUNG Galaxy Store). To find the app, use the keyword “SmartThings”. NOTE • SmartThings is incompatible with some tablets and some mobile devices.• Some iPad...

APPENDIX 4 [Android] The connection to your device will be progressed automatically. – [iOS] Open the setting app, and select [vacuum]_E30AJT** in the Wi-Fi list. 5 Provide the authentication when you are directed to do so. 6 [Android] The connection to your wireless router will be progressed automa...

APPENDIX Functions of the SmartThings App Classification Functions Explanation Monitoring Cleaning Report • You can check the result of the last cleaning.• You can check the histories of last 50 cleanings. Control Dock • You can stop cleaning and have the Jet Bot return to the Docking Station. Pause...

APPENDIX Installation NOTE • Install the Docking Station in a place where the floor and wall are level.• If the cleaning area is wooden floors, it is best to install the Docking Station along the grain of wooden floors. • If the power switch is off, the Jet Bot will not charge even if it is docked o...

APPENDIX • If the Jet Bot is left detached from the Docking Station, the battery will drain naturally. – Try to keep the Jet Bot being charged on the Docking Station. (However, turn off the power switch and leave the Docking Station unplugged when planning to leave the house for long periods of time...

APPENDIX Battery usage NOTE • When you purchase a battery, check the SAMSUNG logo ( ) attached on the battery and the model name, then contact a service center. • This battery is exclusively for the SAMSUNG Electronics Jet Bot. Do not use it for any other products or purposes. • Do not disassemble o...

APPENDIX Corrective measures before reporting a problem 1 The Status Indicator turns red and blinks with a voice guide. 2 Turn off the power switch and check the instructions below and take appropriate actions. 3 When turning the Jet Bot on by pressing the power switch, the Status Indicator turns wh...

APPENDIX Troubleshooting Symptom Checklist The Jet Bot is not working at all. • Check if the power switch is on.• Check if the Status Indicator is on.• Check if the Jet Bot's battery is depleted. – When the Jet Bot’s Status Indicator turns red and stays red, place the Jet Bot manually on the Docking...

APPENDIX Open Source Announcement The software included in this product contains open source software. To obtain the source code covered under licenses which have the obligation of publishing source code (e.g. GPL, LGPL… etc), please visit http://opensource.samsung.com/ and search by model name. It ...

APPENDIX Product Specification Classification Items VR30T80**** series Mechanical specifications Weight 3.4 kg Cleaning method LiDAR location recognition Button method of the Jet Bot Touch type Electrical specifications Power consumption of the Jet Bot 60 W (Spot Clean) Battery specification Lithium...

APPENDIX Memo English 45 1_DJ68-00857F-03_IB_VR8000_WA_EN.indd 45 2023-12-06 오후 11:06:48