Pelco PV1016RN - Manual
Pelco PV1016RN – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PV110 Modem DIP Switch Settings; Programming a Transmitter Number for Call-up; NOTE; Site; Dialing a Transmitter Phone Number; Figure 2. Front Panel
- Page 3 – Hardware Setup; PV1016TN Transmitter with PV120 Terminal Adapter*; BACK-TO-BACK RECEIVER AND TRANSMITTER SETUP; SETTING UP A TRANSMITTER TO RECEIVE A CALL
- Page 4 – TROUBLESHOOTING; PROBLEM; Transmitter, PV1016T models
PelcoVision
™
PV1000 Series
Quick Start Guide
INTRODUCTION
The purpose of this document is to provide the experienced CCTV/electronics user a logical quick start to the PelcoVision™ Phone
Line Transmission System. This document will detail the minimum steps necessary to transmit and receive video using the
PelcoVision™ system. For detailed installation, programming and operating instructions refer to the PelcoVision™ I/O Manual
(C1913M).
Recommendations
PSTN Models: Pelco does not recommend using a PBX phone connection for the PV110 modem due to the possibility of
bandwidth limitations or digital voltages. If at all possible, use a true analog, FAX grade phone connection.
ISDN Models: Pelco recommends using the AT&T 5ESS switch type using the Multipoint/Initializing switch version,
configured for the Adtrans Express 3000. However, the ISDN switch type and switch is not critical as long as it supports
Asynchronous Bonding.
SETTING UP THE RECEIVER TO CALL A TRANSMITTER
This section will provide the minimum details necessary to establish a phone line connection between the PV1016R(N) and the
PelcoVision™ demonstration site (PSTN telephone number 1-888-294-1560) or another known PelcoVision™ Transmitter (see
Setting Up a Transmitter to Receive a Call).
Hardware Setup
■
Remove the DIP switch cover from the rear of the Receiver and set SW 1 and SW 2 according to model. Refer to Figure 1
when setting DIP switches and making cable connections to the PV1016R.
PV1016R (with PV110 Modem)
1
2
3
4
5
6
7
8
SW 1
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
SW 2
ON
OFF
OFF
OFF
N/A
N/A
N/A
N/A
PV1016RN (with PV120 ISDN Terminal Adapter)*
1
2
3
4
5
6
7
8
SW 1
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
SW 2
ON
OFF
OFF
OFF
N/A
N/A
N/A
N/A
*Program the PV120 in accordance with the instructions included in the PV120 package prior to connecting it to the Receiver. It must
match the configuration of the PV120 used for the Transmitter. DIP switch settings for the PV120 are correct out of the box.
SW1
SW2
MODEM
COM 2
COM 1
MONITOR 2
MONITOR 1
KEYBOARD
MONITOR OUTPUT
SW 2
SW 1
MODEM PORT
AC POWER
REAR
C1913M-QS (9/99)
Figure 1. PV1016R Rear Panel
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
■ Set the DIP switches on the rear of the PV110 modem according to the table below. PV110 Modem DIP Switch Settings 1 2 3 4 5 6 7 8 ON ON OFF OFF ON ON OFF OFF ■ Connect the modem or terminal adapter to the Receiver using the supplied cable. ■ Connect the Receiver to an approved power source. ■ Conn...
Hardware Setup ■ Remove the DIP switch cover from the rear of the Transmitter and set SW 1 and SW 2 according to the appropriate table. PV1016T Transmitter with PV110 Modem 1 2 3 4 5 6 7 8 SW 1 ON ON OFF OFF ON ON OFF OFF SW 2 ON OFF OFF OFF OFF OFF OFF OFF PV1016TN Transmitter with PV120 Terminal A...
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE FIX ■ Cannot access the telephone Receiver is configured in the Leased Set the DIP switches on the back of the directory to call Transmitter site. Line mode. Receiver to the correct modem setting. ■ Selected number does not dial Telephone number is programmed i...
