Pelco ICIMI1000 - Manual - manualsarea.com

Page 2 - ii; CONTENTS; LIST OF ILLUSTRATIONS

16 Pelco Manual C1014M-B (10/97) ii CONTENTS Section Page 1.0 GENERAL .................................................................................................. 1 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 11.2 UNPACKING INSTRUCTIONS ..................................

Page 3 - Only use replacement parts recommended by Pelco.; The product and/or manual may bear the following marks:; RISK OF

Pelco Manual C1014M-B (10/97) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation a...

Page 4 - UNPACKING INSTRUCTIONS; Unpack and inspect all parts carefully.

2 Pelco Manual C1014M-B (10/97) 1.2 UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully. The following items are supplied: 1 ICIMI1000 Interface Cable 1 Installation/Operation Manual (C1014M-B) 1 Interface Extension Cable Be sure to save the shipping carton, boxes and inserts. They are the...

Page 6 - INSTALLATION FOR CASH REGISTERS; LOCATING THE PRINTER CONNECTION; Installation

4 Pelco Manual C1014M-B (10/97) 3.0 INSTALLATION FOR CASH REGISTERS This section covers the installation of the ICIMI1000 interface cable with the GilbarcoTCR/15 and “G-Site”; Koppens/Schlumberger Micromax 1000, 2000, 3000 Pro;Suntronics Station Minder 890, 960, 2000; and Verifone Ruby Super System ...

Page 7 - Proceed to the section for your specific cash register.; The connection for the cus-

Pelco Manual C1014M-B (10/97) 5 To define communication parameters for baud rate, type in the appropriatedata and press “ENT” to save. To define all the other communication param-eters, type the appropriate data for each parameter. (Refer to the section forProcedures for the Verifone Ruby Super Syst...

Page 8 - Because the baud rate of

6 Pelco Manual C1014M-B (10/97) 3.2.2 Procedures for the Gilbarco “G-Site” Cash Registers The following procedures are to be performed on the Gilbarco “G-Site” Cash Reg-isters: 1. Use the 8-pin modular adapter supplied with the ICIMI1000 when interfacingto this register. 2. Be sure the cables on the...

Page 9 - must

Pelco Manual C1014M-B (10/97) 7 3.2.4 Procedures for the Suntronics Station Minder 890, 960, and 2000 Cash Registers The following procedures are to be performed on the Suntronics Station Minder890, 960, and 2000 Cash Registers 1. Be sure the cables on the wiring kit are connected to the yellow and ...

Page 10 - WIRING KITS

8 Pelco Manual C1014M-B (10/97) 5. Verifone uses the Epson Model TM930II as the standard printer on this regis-ter. If you are using the Epson Model TM950II printer, with 9-pin “D” styleconnector, you will need to use the Pelco ICIDRP interface cable. 6. Set the SW1 switch on the ICIMI1000 interface...

Page 12 - INSTALLATION FOR ATM MACHINES; PREPARATION; The ATM protocols that Pelco supports are:; CONNECTING THE INTERFACE; interface cable connection between the ATM machine and the; PROGRAMMING

10 Pelco Manual C1014M-B (10/97) 4.0 INSTALLATION FOR ATM MACHINES This section covers the installation of the ICIMI1000 interface cable with the Diebold,IBM, and NCR ATM machines. 4.1 INTER-CHECK ® PREPARATION 1. Check to see if Pelco supports the communication protocol your ATM is run-ning. ATMs h...

Page 13 - ATM Machine Interface Cable Installation

Pelco Manual C1014M-B (10/97) 11 Figure 3. ATM Machine Interface Cable Installation AT M M A C H I N E AT M N E T W O R K M O D E M P L A C E I N T E R FA C E C A B L E H E R E( I C I M I 1 0 0 0 )

Page 14 - If your protocol is Diebold

12 Pelco Manual C1014M-B (10/97) 4.3 INTER-CHECK ® PROGRAMMING 1. Select the appropriate communication protocol your ATM is using. Refer toyour Inter-Check ® manual for a complete explanation on proper programming. 2. Set the ATM device addresses to “00”. 3. Make sure the Inter-Check ® unit receives...

Page 15 - GENERAL; Indoor

Pelco Manual C1014M-B (10/97) 13 5.0 SPECIFICATIONS GENERAL Environment: Indoor OperatingTemperature: 32 ° to 120 ° F (0 ° to 49 ° C) Weight Unit Shipping 0.45 lbs (0.20 kg) 0.60 lbs (0.27 kg) Connectors: One (1) male 25 pin D-SUB connectorOne (1) female 25 pin D-SUB connectorOne (1) RJ-14 male conn...

Page 16 - WARRANTY AND RETURN INFORMATION; WARRANTY; RETURNS

14 Pelco Manual C1014M-B (10/97) 6.0 WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit,Genex, Legacy, and Spectra are registeredtrademarks of Pelco.Endura and ExSite are trademarks of Pelco. © Copyright 1997, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, ...

Pelco ICIMI1000 - Manual

Table of Contents:

Summary

Other Pelco Models