Page 3 - Contents
3 C 2258 M (5/11) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Package Contents . . . . . . . . . . . . . ....
Page 4 - List of Illustrations
4 C 2258 M (5/11) List of Illustrations 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Package Contents Continued . ...
Page 5 - Important Safety Instructions
5 C 2258 M (5/11) Important Safety Instructions 1 . Read these instructions .2 . Keep these instructions .3 . Heed all warnings .4 . Follow all instructions .5 . Prior to the installation of this product, the installation instructions should be read and completely understood . The installation instr...
Page 6 - PACKAGE CONTENTS
6 C 2258 M (5/11) PACKAGE CONTENTS Figure 1. Package Contents Tilt Wall Mount Parts: Wall Plate (1 ea .) Mounting Brackets (2 ea .) 5/16" Flat Washers (6 ea .) Universal Spacers (24 ea .) Security Barrel (1 ea .) Universal Washers (6 ea .) Thread Depth Indicator (1 ea .) Pro Mounting Hardware Pa...
Page 8 - Installing the Wall Plate
8 C 2258 M (5/11) Installing the Wall Plate Directional Mounting Arrow The Directional Mounting Arrow stamped into the top of the PMCLNBWMT wall mount indicates which edge is the top (Figure 3) . Mounting Safety Two people are recommended for the installation of this mount . Figure 3. Locating the D...
Page 9 - WOOD STUD INSTALLATION
9 C 2258 M (5/11) You must secure the wall plate to two wall studs with a minimum of four lag bolts (two lag bolts for each stud found) . 1 . Use a stud finder (not included) to determine the exact center of wall studs in the vicinity of the wall plate . 2 . Use a pencil (not included) to mark the e...
Page 12 - CONCRETE INSTALLATION
12 C 2258 M (5/11) 13 . Insert one 5/16" x 3" lag bolt and one 5/16" washer into each pilot hole (Figure 11) .14 . Tighten all lag bolts using a socket wrench and ½" socket . Do not overtighten the lag bolts when attaching the mount to the wall . Improper installation may result in p...
Page 15 - STEEL STUD INSTALLATION
15 C 2258 M (5/11) STEEL STUD INSTALLATION The supplied M6 steel stud anchors must be used to install the mount to steel studs . Do not use lag bolts or wood screws (Figure 18) . Steel Stud Anchor Screw Steel Stud Anchor Sleeve Figure 18. Steel Stud Components 1 . Identify the general location on th...
Page 18 - . Marking the Depth Above the Threaded Insert; SELECTING THE MOUNTING HARDWARE
18 C 2258 M (5/11) Installing the Mounting Bracket 1 . Insert a small straw or toothpick into the threaded inserts found on the back of the flat-panel .2 . Use a pencil to mark the depth of the threaded insert on the small straw or toothpick .3 . Mark the straw or toothpick 1/8" above the depth ...
Page 19 - UNIVERSAL WASHER INSTALLATION
19 C 2258 M (5/11) UNIVERSAL WASHER INSTALLATION The Universal Washers and Spacers are designed to accommodate the various M4, M5, M6 and M8 hole sizes required by flat-panels (Figure 27) . Do not place excessive pressure on the back of the flat-panel, as this may damage your flat-panel . The Univer...
Page 20 - UNIVERSAL SPACER INSTALLATION
20 C 2258 M (5/11) UNIVERSAL SPACER INSTALLATION Universal Spacers allow you to attach the mounting bracket to flat-panels which have recessed or uneven mount points . Each Universal Spacer adds ¼" to the distance between the mounting bracket and your flat-panel . The Universal Spacers must be s...
Page 21 - ATTACHING THE MOUNTING BRACKET TO THE FLAT-PANEL
21 C 2258 M (5/11) ATTACHING THE MOUNTING BRACKET TO THE FLAT-PANEL This section presumes that you have read and understood these sections: • Selecting the Proper Mounting Hardware • Universal Washer Installation • Universal Spacer Installation 1 . Place your flat-panel screen-side down on a soft, f...
Page 24 - LEVELING SCREW ADJUSTMENT; LOCKING SCREW ADJUSTMENT
24 C 2258 M (5/11) Mounting Bracket Adjustments If your flat-panel is tilted too far to one side, the leveling screws will allow you to compensate for this tilt by simply adjusting the screws with a screwdriver .1 . Loosen both locking screws (Figure 35) .2 . Adjust the tilt of your flat-panel .3 . ...
Page 25 - Tilt Adjustment; ADJUSTING THE FLAT-PANEL FRICTION TILT ANGLE; ADJUSTING THE FLAT-PANEL TO THE ORIGINAL POSITION
25 C 2258 M (5/11) Tilt Adjustment 1 . Place one hand at the center top edge of the flat-panel .2 . Place the other hand on the center bottom edge of the flat-panel .3 . Using the upper hand, gently pull the top of the flat-panel towards you while the lower hand gently pushes the bottom of the flat-...
Page 26 - Utilizing the Security Barrel; Technical Specifications
26 C 2258 M (5/11) Utilizing the Security Barrel The mount includes one Security Barrel which can provide additional theft deterrence for your flat-panel when used with a padlock or other locking system (not included) . To use a padlock:1 . Place the locking hook through the hole of the security bar...
Page 27 - Warranty; PRODUCT WARRANTY AND RETURN INFORMATION
27 C 2258 M (5/11) Warranty 2-10-10 The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC . REVISION HISTORYManual# Date Comments C2258M 5/11 Original Version Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Espr...