Pelco FR8316 - Manual

C2603M (6/06) 7 Product Overview DESCRIPTION The FT8316/FR8316 fiber transmitter and receiver provide the ability to transmit up to 16 composite video channels over one optical fiber (refer to Figure 1). Figure 1. Sixteen-Channel Video FT8316 Transmitter and FR8316 Receiver Features of the FT8316/FR...

8 C2603M (6/06) MODELS The FT8316/FR8316 fiber transmitter and receiver consist of the following series of models: Multimode Models:* FT8316MSTR Sixteen-channel fiber optic video transmitter; multimode, ST connector FR8316MSTR Sixteen-channel fiber optic video receiver; multimode, ST connector Singl...

C2603M (6/06) 9 FRONT PANEL The front panel of the FT8316 transmitter and FR8316 receiver provides LED indicators that a llow you to monitor signal status, laser status (transmitter only), and operating power. The following sections provide a view of the front panel of the transmitter and receiver. ...

10 C2603M (6/06) FRONT PANEL - FR8316 RECEIVER Figure 3 illustrates the front panel of the FR8316 receiver. Figure 3. Front Panel of FR8316 Receiver For detailed information about the front-panel indicators, refer to the Troubleshooting section. VIDEO PRESENT LEDs 1-16 OPTIC FAULT LED, optical signa...

C2603M (6/06) 11 REAR PANEL Connections to the FT8316 transmitter and FR8316 receiver are made to the rear panel of the modules (refer to Figure 4). Figure 4. Rear Panel of FT8316 Transmitter and FR8316 Receiver For additional information about rear-panel connections, refer to the Installation secti...

12 C2603M (6/06) Installation PACKAGE CONTENTS The following items are supplied: 1 FT8316 transmitter or FR8316 receiver 1 Regulated switching power supply with either of the following: • Four plug adapters (North American, Australian, U.K., and European); 100-240 V AC, 50-60 Hz input, 12 VDC (25 W)...

C2603M (6/06) 13 CONNECTIONS Connections to the FT8316 transmitter and FR8316 receiver are made on the rear panel of the modules and consist of the following: • Power connection NOTES: – A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when used as a stand-alone module. ...

14 C2603M (6/06) Troubleshooting LED indicators on the front panel of the FT8316 transmitter and FR8316 receiver (refer to Figure 2 and to Figure 3, respectively) allow you to monitor signal status , laser status (transmitter only), and operating power. Table A provides information about the front-p...

C2603M (6/06) 15 Video Present LED (Continued) Red on receiver Incoming video signal is not present on the channel. Optical signal is not being received from the trans-mitter. Optic Fault LED is also red. Refer to the Optic Fault LED - Receiver section in this table. Video source is not powered on. ...

16 C2603M (6/06) Optic Fault LED - Receiver Green The optical signal is being received from the transmitter. – No action required. Red The optical signal is not being received from the transmitter. Transmitter is not powered on. Check power connections. Replace power supply if necessary. Fiber optic...

C2603M (6/06) 17 Specifications VIDEO Number of Channels 16 Modulation Type Pulse code modulation, 8-bit resolution Video Input (FT8316)/ 1.0 Vp-p, 75 ohms; NTSC, PAL, and SECAM Video Output (FR8316) Bandwidth 6.5 MHz Gain Unity Crosstalk -50 dB typical at 3.58 MHz Differential Gain <1% Different...

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic ...