Pelco CM6800-32X6 - Manual

Pelco CM6800-32X6

Pelco CM6800-32X6 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
Page: / 20

Table of Contents:

  • Page 2 – Worldwide, there’s so much we can show you.
  • Page 3 – Pycc; NN
  • Page 4 – Step 4. Switch cameras and select monitors.; Figure 2. Connecting Multiple M Devices; devices are needed, connect as illustrated below.; Access programming mode:; NOTE: On the KBD960/KBR960 you must first select; Set DIP switch 2 to the ON position.
  • Page 5 – English; Figure 3. PC Connection; Identify each camera’s receiver control type as PTZ-A.; CAMERA/RECEIVER CONFIGURATION; Refer to the appropriate camera installation manual for; PC; DRY CONTACT
  • Page 6 – Figura 2. Conexión de Múltiple Dispositivos; Paso 1. Instalar el CM6800 y todos los componentes de su; SEGUNDOS antes de continuar.; Paso 4. Cambiar cámaras y seleccionar monitores.; NOTA: En el KBD960/KBR960 primero debe seleccionar; CONFIGURACIÓN POR DEFECTO DE COM 3:
  • Page 7 – Español; Figura 3. Conexión a PC; CABLE DE MODEM NULO; CONTACTO SECO; CONFIGURACIÓN CÁMARA/RECEPTOR
  • Page 8 – Figura 2. Conexão de diversos aparelhos M; Ligar a eletricidade do sistema.; OBSERVAÇÃO: No KBD960/KBR960, primeiro é necessário selecionar; Ajustes dos aparelhos:
  • Page 9 – Portuguese; Figura 3. Conexão para o computador; CABO DE MODEM NULO; CONTATO A SECO; CONFIGURAÇÃO DO RECEPTOR/CÂMARA
  • Page 10 – CM6800 und alle Systemkomponenten installieren.; HINWEIS: Am KBD960/KBR960 müssen Sie zuerst; Gerätehandbuch zu finden.; KBD960 Einstellungen:; Wählen Sie die Baudrate und stellen Sie die lokale Adresse ein.
  • Page 11 – Deutsch; Abbildung 5. Alarmverbindungen; NULLMODEMKABEL; TROCKENKONTAKT; KAMERA/EMPFÄNGERKONFIGURATION; In der jeweiligen Kamerainstallationsanleitung finden Sie die
  • Page 12 – Figure 2. Connexion de plusieurs dispositifs M; Mettez le système en route.; PARAMÈTRES PAR DÉFAUT DU COM 3 :
  • Page 13 – Français; Figure 3. Connexion PC; CÂBLE MODEM NUL; CONTACT SEC; PTZ-A. Configurez le port PTZ-A en fonction du type de communication; CONFIGURATION DES CAMÉRAS/RÉCEPTEURS; la configuration et le schéma d’adressage.
  • Page 14 – Figura 2. Collegamento di dispositivi M Multipli; Installare l’unità CM6800 e tutti i componenti del sistema.; NOTA: sul KBD960/KBR960 vanno prima selezionati; IMPOSTAZIONI PREDEFINITE COM 3:; Accendere il collegamento elettrico.; Impostazioni di KBD960:; Entrare nella modalità Impostazione.
  • Page 15 – Italiano; Figura 3. Collegamento PC; CAVO MODEM NULLO; CONTATTO A SECCO; CONFIGURAZIONE DELL’UNITÀ CM6800; configurazione e d’indirizzamento.
  • Page 17 – Polski
Loading the manual

CM6800-32X6 MATRIX SWITCHER

Quick Start Guide

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Worldwide, there’s so much we can show you.
Page 3 - Pycc; NN

English Español Portuguese Deutsch Français Italiano Polski Pycc K NN ˘

Page 4 - Step 4. Switch cameras and select monitors.; Figure 2. Connecting Multiple M Devices; devices are needed, connect as illustrated below.; Access programming mode:; NOTE: On the KBD960/KBR960 you must first select; Set DIP switch 2 to the ON position.

Step 1. Install the CM6800 and all components of yoursystem. Refer to the Quick Start illustrations for an overview of system connections. Step 2. Power-up the system. Video from camera 1 and the Time/Date Stamp appears on all system monitors. The time stamp advances in one-second increments. WAIT F...

Other Pelco Models

All Pelco Other