Pelco 100 Series - Manual

Pelco 100 Series

Pelco 100 Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
Page: / 16

Table of Contents:

  • Page 2 – LIST OF ILLUSTRATIONS; Figure; CONTENTS; Section
  • Page 3 – C A U T I O N; IMPORTANT SAFEGUARDS AND WARNINGS; around the bolt holes between the enclosure and mounting surface.; REGULATORY NOTICES; • Reorient or relocate the receiving antenna.
  • Page 4 – WELCOME; Thank you for purchasing Pelco’s Camclosure
  • Page 5 – INSTALL THE BACK BOX; REMOVE THE LOWER DOME; Refer to Figure 1 for the following steps.; I M P O R T A N T; Installation Directly to a Wall/Ceiling
  • Page 6 – Installation on a 4S Electrical Box; Attach Directly to Concrete Wall/Ceiling; Refer to Figure 2 for the following steps.; Not Using Side Conduit Opening; - Verify the set screw and side conduit cover are tight.; Using Side Conduit Opening; - Loosen the set screw and remove the conduit plug. Install a; Attach to a 4S Electrical Box; flat head screws supplied.
  • Page 7 – Mount to a Plaster Ring; Pull video and power wires into the base.
  • Page 8 – Terminal Block for Input Power; CONNECT POWER WIRES; DC Operation
  • Page 9 – INSTALL THE CAMERA MODULE; CHECK HEATER JUMPER; Heater Jumper and Camera Connector Locations
  • Page 10 – Wall Mounting; Ceiling Mounting; – The camera bracket; INSTALL AND POSITION THE CAMERA; Turn on power to the camera and monitor.
  • Page 11 – MAKE CAMERA SETTINGS
  • Page 12 – ON; Enables the AGC mode.; Disables the AGC mode.; OFF; center of the picture appears dark or as a silhouette.; VERTICAL PHASE ADJUSTMENT (24 VAC OPERATION ONLY); To synchronize the cameras:; VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT
  • Page 13 – Window Adjustment; REINSTALL THE LOWER DOME AND TRIM RING; Position the viewing window over the lens of the camera.
  • Page 14 – SPECIFICATIONS; BACKBOX
  • Page 15 – REVISION HISTORY; WARRANTY AND RETURN INFORMATION
Loading the manual

100 Series Camclosure

®

Integrated Camera System

With LowLight

™

DSS Technology

C2460M-A (7/03)

®

I N S TA L L AT I O N / O P E R AT I O N

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - LIST OF ILLUSTRATIONS; Figure; CONTENTS; Section

2 C2460M-A (7/03) LIST OF ILLUSTRATIONS Figure Page 1 Installation Directly to a Wall/Ceiling .......................................................................................... 5 2 Installation Directly to a Concrete Wall/Ceiling .................................................................

Page 3 - C A U T I O N; IMPORTANT SAFEGUARDS AND WARNINGS; around the bolt holes between the enclosure and mounting surface.; REGULATORY NOTICES; • Reorient or relocate the receiving antenna.

C2460M-A (7/03) 3 Heater elements could be hot! When camera power is on, use cautionwhen adjusting the camera. C A U T I O N IMPORTANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specif...

Page 4 - WELCOME; Thank you for purchasing Pelco’s Camclosure

4 C2460M-A (7/03) WELCOME Thank you for purchasing Pelco’s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology. Your new ICS100 Series surface mount dome system includes ahigh-resolution, low light, color camera with auto iris and varifocal lens. The LowLigh...

Other Pelco Models

All Pelco Other