Pelco 100 Series - Manuals - manualsarea.com

Page 2 - LIST OF ILLUSTRATIONS; Figure; CONTENTS; Section

2 C2460M-A (7/03) LIST OF ILLUSTRATIONS Figure Page 1 Installation Directly to a Wall/Ceiling .......................................................................................... 5 2 Installation Directly to a Concrete Wall/Ceiling .................................................................

Page 3 - C A U T I O N; IMPORTANT SAFEGUARDS AND WARNINGS; around the bolt holes between the enclosure and mounting surface.; REGULATORY NOTICES; • Reorient or relocate the receiving antenna.

C2460M-A (7/03) 3 Heater elements could be hot! When camera power is on, use cautionwhen adjusting the camera. C A U T I O N IMPORTANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specif...

Page 4 - WELCOME; Thank you for purchasing Pelco’s Camclosure

4 C2460M-A (7/03) WELCOME Thank you for purchasing Pelco’s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology. Your new ICS100 Series surface mount dome system includes ahigh-resolution, low light, color camera with auto iris and varifocal lens. The LowLigh...

Page 5 - INSTALL THE BACK BOX; REMOVE THE LOWER DOME; Refer to Figure 1 for the following steps.; I M P O R T A N T; Installation Directly to a Wall/Ceiling

C2460M-A (7/03) 5 INSTALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper-resistant screws with the supplied 1/8-inch hollow screwdriver bit. Remove thelower dome and place it to the side. INSTALL THE BACK BOX The installation methods for the ICS100 back boxinclude the following: • Attach Direc...

Page 6 - Installation on a 4S Electrical Box; Attach Directly to Concrete Wall/Ceiling; Refer to Figure 2 for the following steps.; Not Using Side Conduit Opening; - Verify the set screw and side conduit cover are tight.; Using Side Conduit Opening; - Loosen the set screw and remove the conduit plug. Install a; Attach to a 4S Electrical Box; flat head screws supplied.

6 C2460M-A (7/03) Figure 3. Installation on a 4S Electrical Box 8-32 X .750 FLAT HEAD SCREW (SUPPLIED) 8-32 X .375 PAN HEAD SCREW (SUPPLIED) WALL OR CEILING ADAPTER PLATE BASE 4S ELECTRICAL BOX Attach Directly to Concrete Wall/Ceiling Refer to Figure 2 for the following steps. 1. Attach the base to ...

Page 7 - Mount to a Plaster Ring; Pull video and power wires into the base.

C2460M-A (7/03) 7 Mount to a Plaster Ring Refer to Figure 4 for the following steps. Installation instructions assume that the 4S electrical boxand plaster ring were previously installed. 1. Pull video and power wires into the base. 2. Attach the base to the plaster ring. - Use the two 8-32 x .750-i...

Page 8 - Terminal Block for Input Power; CONNECT POWER WIRES; DC Operation

8 C2460M-A (7/03) Figure 5. Terminal Block for Input Power CONNECT POWER WIRES Depending on the input voltage, connect either the 12 VDC or 24 VAC input power wires to theterminal block inside the base. Refer to Figure 5 for the location of the terminal block. DC Operation – Refer to the enlarged po...

Page 9 - INSTALL THE CAMERA MODULE; CHECK HEATER JUMPER; Heater Jumper and Camera Connector Locations

C2460M-A (7/03) 9 INSTALL THE CAMERA MODULE CHECK HEATER JUMPER The Camclosure is equipped with a heater to defrost the dome. Some installations may not requirethis heater. If the unit will never be subjected to a frost temperature, you can disable the heater,saving power requirements. To disable th...

Page 10 - Wall Mounting; Ceiling Mounting; – The camera bracket; INSTALL AND POSITION THE CAMERA; Turn on power to the camera and monitor.

10 C2460M-A (7/03) Wall Mounting – The camera bracket tab points out of the enclosure and thetop of the camera points up towardsthe tab. Ceiling Mounting – The camera bracket tab points out of the enclosure and the topof the camera is pointed in the oppositedirection. CAMERA BRACKETTAB ALWAYS POINTS...

Page 11 - MAKE CAMERA SETTINGS

C2460M-A (7/03) 11 Figure 7. Default Switch Settings and Location of Camera Adjustments ZOOM/FOCUS 1. Select a field of view by turning the zoom adjustment ring. Refer to Figure 7.2. Tighten the zoom locking screw.3. Adjust the focus by moving the focus locking screw clockwise/counterclockwise.4. Ti...

Page 12 - ON; Enables the AGC mode.; Disables the AGC mode.; OFF; center of the picture appears dark or as a silhouette.; VERTICAL PHASE ADJUSTMENT (24 VAC OPERATION ONLY); To synchronize the cameras:; VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT

12 C2460M-A (7/03) AGC (AUTOMATIC GAIN CONTROL) AGC automatically adjusts the image to compensate for changes in light levels. ON (Default setting) – Enables the AGC mode. OFF – Disables the AGC mode. BLC (BACK LIGHT COMPENSATION) The BLC (backlight compensation) feature compensates for backlit scen...

Page 13 - Window Adjustment; REINSTALL THE LOWER DOME AND TRIM RING; Position the viewing window over the lens of the camera.

C2460M-A (7/03) 13 Figure 8. Window Adjustment REINSTALL THE LOWER DOME AND TRIM RING 1. Domes with Liners (only) – Position the viewing window over the lens of the camera. a. Loosen the three Phillip screws located in the dome. b. Insert the blade of a standard screwdriver in one of the adjustment ...

Page 14 - SPECIFICATIONS; BACKBOX

14 C2460M-A (7/03) SPECIFICATIONS BACKBOX Electrical Input Voltage: 12 VDC or 24 VAC, ±10%, auto-sensing Power Consumption: 13 watts or less Video Connector: BNC General Operating Temperature: -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Pan/Tilt Adjustment: Manual; 360° pan; 180° tilt Constr...

Page 15 - REVISION HISTORY; WARRANTY AND RETURN INFORMATION

C2460M-A (7/03) 15 REVISION HISTORY Manual # Date Comments C2460M 4/03 Preliminary manual for beta testing. C2460M-A 7/03 Final version. ® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. © Copyright 2003, Pelco. All rights reserved. WARRANTY ...