Page 3 - CONTENTS; LIST OF ILLUSTRATIONS
Pelco Manual C581M-B (1/04) 3 CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 4REGULATORY NOTICES .................................................................................................. 4 DESCRIPTION ...................
Page 4 - IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement parts recommended by Pelco.; REGULATORY NOTICES; Reorient or relocate the receiving antenna.
4 Pelco Manual C581M-B (1/04) IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. Unless the unit is specifically...
Page 5 - DESCRIPTION
Pelco Manual C581M-B (1/04) 5 DESCRIPTION The KBD4002 Genex ® Multiplexer Keyboard is a full-function keyboard controller for the Genex MX4000 Multiplexer and the Genex MX4000SVR Multiplexer Server. This manual covers the KBD4002 keyboard’s operation with the duplex and simplex modelsof the multiple...
Page 6 - INSTALLATION; The following parts are supplied:; MULTIPLEXER MODE INSTALLATION; Set switch 7 ON if you want to address all cameras consecutively.
6 Pelco Manual C581M-B (1/04) INSTALLATION The following parts are supplied: 1 KBD4002 keyboard 1 25-foot (7.6 m) data cable There are two modes of operation–multiplexer mode and multiplexer server mode–dependingon whether the keyboard is connected to a multiplexer or to a server. In the multiplexer...
Page 7 - MULTIPLEXER SERVER MODE INSTALLATION; ADDRESS; Keyboard Addresses; Keyboard; Switch Locations and RJ-45 Jack Pinouts
Pelco Manual C581M-B (1/04) 7 3. Replace the cover on the back of the keyboard. 4. A 25-foot (7.6 m) data cable with RJ-45 connectors is supplied with the keyboard. Plugone end of the cable into the back of the keyboard and plug the other end into theCOM IN connector on the back of the multiplexer. ...
Page 8 - OPERATION; IMPORTANT NOTE ABOUT PROGRAMMING; To allow the keyboard to communicate with multiplexers in the
8 Pelco Manual C581M-B (1/04) Set switch 7 ON if you want to address all cameras consecutively. Set switch 7 OFF if you want to address cameras according to the multiplexer they areconnected to. PROGRAMMING MODE Set switch 8 ON to program the server and the multiplexer. Set the switch OFF todisable ...
Page 9 - Programming; IMPORTANT NOTE ABOUT COAXITRON; Camera Setup
Pelco Manual C581M-B (1/04) 9 2. If you have more than one multiplexer, each one must have its own address (Unit ID inthe Advanced System Setup menu). If you have a server, the multiplexer addressmust match the input on the server to which it is connected; for example, if the multi-plexer is connect...
Page 10 - Provide motion control to receiver and; KBD4002 Keyboard Definitions
10 Pelco Manual C581M-B (1/04) 1. LED DISPLAY Displays the address of the multiplexer (from 1-16) with which the keyboard is communicating. 2. LIVE/VCR KEY Selects the source of video to display on the monitor(s). LIVE is live video from the cameras.VCR is recorded video that is played back from a V...
Page 11 - Operation Guide
Pelco Manual C581M-B (1/04) 11 Table B. Operation Guide NOTE: References to switch 7 in this table refer to the switch behind the panel on the back of the keyboard. There are two modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (switch 7 ON, refer to Table C) or b...
Page 19 - PROGRAMMING; IMPORTANT NOTE; Use the arrow buttons to move the cursor to UNIT ID.; Whenever a; Multiplexer
Pelco Manual C581M-B (1/04) 19 PROGRAMMING This section applies only to programming the multiplexer. To program themultiplexer server, refer to the server manual. Programming allows you to configure the multiplexer from the KBD4002 for the way thatyou want your system to operate. The multiplexer aut...
Page 20 - PASSWORD; Advanced; MENUS; To program the main basic system parameters:; Time and Date; Set the current time and date. The time uses a 24-hour clock.; Time Display; Once you are in a
20 Pelco Manual C581M-B (1/04) PASSWORD You can program the multiplexer to request a password for access to programming menus.The password is enabled in the Advanced System Setup menu (refer to the Advanced System Setup section). The universal password is 3916 and cannot be changed. This password mu...
Page 21 - Title Display shows a
Pelco Manual C581M-B (1/04) 21 Title Display (Duplex Multiplexer) ON - Displays camera titles and the word LIVE or VCR on the main monitor.OFF - Camera titles and the word LIVE or VCR are not shown on the main monitor. Title Display (Simplex Multiplexer) ON - Displays camera titles on the main monit...
Page 22 - Date Format; Sets the format for displaying the date on the main monitor.; Password; Advanced System Setup Menu
22 Pelco Manual C581M-B (1/04) ADVANCED SYSTEM SETUP (View Key) To program the advanced main system parameters: 1. Press the MAIN MONITOR key. 2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard isconnected to a multiplexer; 1-8 if the keyboard is connected to a se...
Page 23 - When; Troubleshooting
Pelco Manual C581M-B (1/04) 23 Spot Monitor Display If you want the spot monitor to switch to cameras that have alarms or activitydetection, select BLANK, SEQUENCE, or TRACK MAIN, then under RESPONDS TOselect ALARMS, ACTIVITY, or ALARMS/ACTIVITY. If you are using the spot monitorfor normal video and...
Page 25 - NTSC; UNIVERSAL
Pelco Manual C581M-B (1/04) 25 Figure 5. Basic VCR Setting Menu Table D. VCR Types NTSC PAL UNIVERSAL UNIVERSAL GYYR TLC1800 ASUTA TLVCR 251 GYYR 2100 ASUTSA TLVCR 964 GYYR 2100 HD MODE BURLE TC3910X JVC SR-L900U HITACHI VTL30E JVC SR-L901U HITACHI VT-L1000E JVC SR-9070U HITACHI VT-L2000E JVC BR-S92...
Page 26 - Custom VCR Setup Menu
26 Pelco Manual C581M-B (1/04) 5. When you have completed all the changes you want to make, go to EXIT. 6. Press the OPEN key to exit the programming mode. When HELP is highlighted, you may press the OPEN key to display a help screen that willtell you which keys to press to configure specific option...
Page 27 - Video Termination; Basic Camera Menu
Pelco Manual C581M-B (1/04) 27 CAMERA SETUP (Number and CAM Keys) To program a camera input: 1. Press the MAIN MONITOR key. 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) a. On the number keypad, enter the address number of the multiplexer (1-16 if thekeyboard is connected to a multi...
Page 28 - Coaxitron Format; OFF - Use when your system has fixed cameras only.; Activity Detection; When you have completed all the changes you want to make, go to EXIT.; The Coaxitron format
28 Pelco Manual C581M-B (1/04) Coaxitron Format EXTENDED - Use when your system has moveable cameras controlled by 32-bitCoaxitron receivers, such as Esprit, Intercept, Spectra, and LRD41C21/LRD41C22Series. OFF - Use when your system has fixed cameras only. STANDARD - Use when your system has moveab...
Page 29 - ACTIVITY DETECTION MASK SETUP; To program an activity detection mask for a camera:; Activity Detection Mask
Pelco Manual C581M-B (1/04) 29 ACTIVITY DETECTION MASK SETUP Activity detection continually monitors selected camera inputs for motion. When motion isdetected, the multiplexer increases the frequency with which that camera(s) is shown andrecorded. Activity detection is most effective when only a few...
Page 31 - HELP MENU; The Help menu is accessed from any other menu.; Camera Sequence Menu
Pelco Manual C581M-B (1/04) 31 HELP MENU The Help menu is accessed from any other menu. 1. Use the pan/tilt keys in any menu to highlight HELP. 2. Press the OPEN key. The Help menu appears. Figure 9. Camera Sequence Menu Figure 10. Help Menu GROUP QUAD (2x2) 1 04 2 04 3 04 4 04 NINE (3x3) 04 04 VCR/...
Page 32 - MULTIPLE CAMERA DISPLAY SETUP; duplex
32 Pelco Manual C581M-B (1/04) MULTIPLE CAMERA DISPLAY SETUP The multiple camera display formats may be configured using the keyboard. The LEDsabove the camera buttons on the multiplexer will illuminate to indicate which cameras arebeing displayed. PROGRAMMING THE PICTURE-IN-PICTURE DISPLAY( Key) Th...
Page 34 - PROGRAMMING MENU DEFAULTS; Programming Menu Defaults; Menu
34 Pelco Manual C581M-B (1/04) PROGRAMMING MENU DEFAULTS Table E. Programming Menu Defaults Menu Item Default System Setup Time Display On Title Display On Normal Record Speed 2/6/8 Hr (NTSC/EIA)3 Hr (PAL/CCIR) Alarm Record Speed 2/6/8 Hr (NTSC/EIA)3 Hr (PAL/CCIR) Main Monitor Video (Duplex Only) Co...
Page 35 - PROGRAMMING A PRESET; set to TRACK MAIN (refer to the; Position the camera using the pan/tilt and lens keys.; must be; set to TRACK MAIN (refer to the; Advanced System Setup; The LEDs above
Pelco Manual C581M-B (1/04) 35 PROGRAMMING A PRESET 1. Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT keylights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item inthe Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup sec...
Page 36 - TROUBLESHOOTING
36 Pelco Manual C581M-B (1/04) TROUBLESHOOTING If you have difficulty operating your system, run through the following checklist to see if youcan solve the problem. 1. Are the keyboard switches set properly? 2. Is the equipment wired properly? 3. Are the menu options in the multiplexer(s) and server...
Page 37 - OR; immediately; SPECIFICATIONS; ELECTRICAL; Power Consumption: 5 watts; KEYBOARD COMMUNICATION; Mechanical; GENERAL
Pelco Manual C581M-B (1/04) 37 18. If the UNIT ID, in the ADVANCED SYSTEM SETUP menu, is inadvertently changed at the keyboard resulting in an uncontrollable sequencing of unit ID numbers and loss ofkeyboard control: a. Go to the multiplexer and press the down arrow button. The sequencing shouldstop...
Page 39 - REVISION HISTORY; Date; PRODUCT WARRANTY AND RETURN INFORMATION
Pelco Manual C581M-B (1/04) 39 REVISION HISTORY Manual # Date Comments C581M 8/99 Original version. C581M-A 9/03 Added Regulatory Notices section and changed power specification. C581M-B 1/04 Revised per ECO #03-9291, software upgrade to increase the number of programmable patterns. Pelco, the Pelco...
